Power cable CEE 7/7 to IEC 320 C13, 10 m length, designed for powering computers and IT equipment. Rated current 10 A, 1 mm conductor, VDE certified. Lanberg CA-C13C-11CC-0100-BK

Module with 8 analog inputs for voltage measurement in the range from 0 to 10 V. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP3084ADAM

Module with three 4-20 mA analog outputs. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP3078ADAM

Module with analog output 0-20 mA or 4-20 mA. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP3076ADAM

Ring light with 12 RGB diodes WS2812B type controlled by serial signal. The module can be powered with the voltage from 3.3 V to 5 V, only one signal line is required to control it. DFRobot DFR0888-12

Module with color sensor TCS3472. The board is equipped with a Grove connector and communicates via the I2C interface. M5Stack U009

The camera is equipped with a Sony IMX378 sensor with a resolution of 12.3 MPx with a wide-angle lens with a viewing angle of 190 °. Dedicated to the Raspberry Pi. Waveshare IMX378-190 12.3MP Camera

The module with a 10 kΩ slide potentiometer and a color LED indicator, designed for the M5Stack sets. M5Stack U123

The module with a gesture detection sensor PAJ7620U2 designed for M5Stack sets. He can recognize 9 gestures and communicates via the I2C interface. M5Stack U127

8" TFT LCD display with touch screen and 5 MP camera. It is equipped with DSI interface for image display and I2C interface for touch panel. Waveshare 8inch DSI LCD (with cam)

Module with a pulse sensor and the level of SpO2 (oxygen saturation level). It is based on the MAX30102 chip and communicates via the I2C or UART interface (Gravity connector). DFRobot SEN0518

Module with a color IPS LCD display with a diagonal of 1.47" and a resolution of 320x172 pixels. It has rounded corners and uses the ST7789 controller (SPI interface). Adafruit 5393

Module with LED driver. It can control LED strips with a length of 1 to 2 meters at a voltage of 9 V or from 1 to 5 meters at a voltage of 12 V. Seeed Studio 105020002

Module with RGB diode and P9813 controller. It is powered with the voltage of 5 V and controlled by the I2C interface (Grove). Seeed Studio 104030006

Module with a black and white OLED display with a diagonal of 1.12" and a resolution of 128x128 px. The board is equipped with a Grove connector and communicates via the I2C and SPI interface. Seeed Studio 104020250

10.1" IPS LCD display with touch panel. Equipped with RGB888 parallel interface for image display and I2C for touch panel operation. Waveshare 10.1inch Capacitive Touch LCD (F)

The module with 4 relays is designed to work with Arduino. It allows you to control devices with operating parameters up to 250VAC/7A or 30VDC/10A. Seeed Studio 103030009

Active HDTV antenna with 28 dB amplification, supporting FullHD and 4K UltraHD standard. Designed for indoor installation. BLOW ATD40

Decoder dedicated to receive digital terrestrial TV programs in the DVB-T2 H.265 standard. Designed for TVs with HDMI, USB, SCART and RF input. BLOW 4625FHD