Stepper motor controller with DRV8825 system
ID: 561436
zł8.30
Tax included
zł6.75 tax excl.
DRV8825 Stepper Motor Driver Carrier is a DRV8825 stepper motor driver that allows you to supply a bipolar current of up to 1.5 A per phase, without using a heat sink. The system can be supplied with voltage up to 45V, in the set there is a heat sink. It is compatible with Polol 2133
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
The stepper motor driver with the DRV8825 system allows the bipolar motor to be supplied with up to 1.5 A current per phase, without the use of a heat sink. The system can be supplied with voltage up to 45V, the set contains a heat sink (maximum current efficiency of the DRV8825 system increases to 2.2A with cooling installed). It is compatible with Polol 2133 .
properties
- Driver module with DRV8825 system
- Possibility to control: full step, half step, 1/4 step, 1/8 step, 1/16 step, 1/32 step
- Adjustable motor current using a potentiometer,
- Intelligent control, automatically selects the correct slope rise mode (fast rise or slow rise)
- Supply voltage: 8.2V-45 V
- Built-in voltage regulator
- Compatible with systems with 3.3V and 5V operating voltages
- Protection: thermal and overcurrent
- Protection against too low input voltage
- Protection against short-circuit to ground and short-circuit of the load
- Four-layer laminate to improve heat dissipation
- Exposed thermal pad on the bottom of the plate (enables the installation of the heat sink)
Included
- Driver module with DRV8825 system
- Radiator with dimensions of 9mm x 9.2mm
561436
Data sheet
- Output current
- 2,2 A
- Number of channels
- 2
- Supply voltage min
- 8,2 V
- Supply voltages max
- 45 V
You might also like
DRV8825 Stepper Motor Driver Carrier is a DRV8825 stepper motor driver that allows you to supply a bipolar current of up to 1.5 A per phase, without using a heat sink. The system can be supplied with voltage up to 45V, in the set there is a heat sink. Polol 2133
zł67.33
24h
Available quantity: 2
Available
Other products in the same category (16)
Pololu High-Power Motor Driver 36v9
zł275.16
24h
Available quantity: 1
Available
DRV8834 Low-Voltage Stepper Motor Driver Carrier
zł39.41
24h
Available quantity: 3
Available
A stepper motor controller that can operate with a voltage range of 24 to 110 VDC or 18 to 80 VAC and a maximum current of up to 8.4 A. It allows micro step configuration in the range of 2 to 256. 2DM860H
zł207.94
24h
Available quantity: 3
Available
Extension board with stepper motor controller based on the STSPIN820 system. Ideally suited for use, among others in 2D / 3D printers, robots, cameras. Pololu 2879
zł91.07
24h
Available quantity: 1
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5056
zł534.64
6 weeks
No product available!
Module with a stepper motor driver based on the DRV8434A system. It allows the bipolar motor to be powered with a current of up to 1.2 A per phase and can be supplied with the voltage from 4.5 V to 45 V. Pololu 3764
zł54.86
6 weeks
No product available!
Module of a 4-channel driver of DC motors with RP2040 microcontroller. It allows the connection of encoders and is equipped with a QW/ST connector. Pimoroni PIM636
zł133.64
24h
Available quantity: 2
Available
TB67S128FTG stepper motor driver module powered by 6.5-44V voltage and 2.1A operating current. The controller allows you to control the movement of the engine with up to 8 different resolutions (up to 1/128 step). Pololu 2998
zł86.89
24h
Available quantity: 2
Available
Extension module with a driver for two stepper motors based on the HR8825 system. Dedicated for Raspberry Pi minicomputers. Waveshare Stepper Motor HAT (B)
zł84.99
4 weeks
No product available!
The Tic 36v4 USB Multi-Interface High-Power Stepper Motor Controller makes basic control of a stepper motor easy. Pololu 3141
zł300.65
24h
Available quantity: 1
Available
The X-NUCLEO-IHM12A1 is a low voltage dual brush DC motor driver expansion board based on the STSPIN240 for STM32 Nucleo. It provides an affordable and easy-to-use solution for the implementation of portable motor driving applications such as thermal printers, robotics and toys
zł56.25
24h
Available quantity: 2
Available
Simple to use stepper motor driver, compatible with anything that can output a digital 0..5V pulse or 0..3.3V pulse. Connect a 4-wire stepper motor and a microcontroller and you’ve got precision motor control! EasyDriver drives bi-polar motors, and motors wired as bi-polar. I.e. 4,6, or 8 wire stepper motors. ROB-12779
zł87.16
24h
Available quantity: 2
Available
Module with a stepper motor driver based on the DRV8434 system. It allows you to power a bipolar motor with a current of up to 1.2 A per phase and a voltage from 4.5 V to 48 V. Pololu 3762
zł45.61
24h
Available quantity: 2
Available
Dual motor controller allowing two DC motors to be driven with voltages from 4.5 to 13.5V and a continuous current of 1.2 A per channel. SparkFun ROB-14450
zł73.10
24h
Available quantity: 1
Available
Pololu Simple Motor Controller 18v7
zł736.12
6 weeks
No product available!
Module with a single-channel driver of DC motors VNH2SP30. It allows you to control a DC motor with a supply voltage of up to 16 V and a current consumption of up to 30 A. Mini Monster Moto Driver
zł97.90
6 weeks
No product available!
DRV8825 Stepper Motor Driver Carrier is a DRV8825 stepper motor driver that allows you to supply a bipolar current of up to 1.5 A per phase, without using a heat sink. The system can be supplied with voltage up to 45V, in the set there is a heat sink. It is compatible with Polol 2133