Segger Target Supply Adapter (8.06.18) - Segger power adapter

Adapter providing two dedicated supply voltages - for programming and powering for the target board. Useful for programming modules that do not support low voltage programming or require a voltage other than 5V. Segger Programming Voltage Adapter (8.06.30)

A compact reference platform that enables rapid testing and verification of trace configurations, providing excellent signal quality for analysis. With the NXP iMX RT1051/52 microcontroller and support for the SWD debug interface, the board provides high performance and flexibility in monitoring system performance. Segger NXP iMX RT1050 Trace Reference Board (6.68.19)

The SEGGER USB Hub is a seven-port, industrial-grade USB hub that provides power to Flasher Compact devices and connects them to the Flasher Hub. Segger USB Hub (5/01/10)

A module that enables precise switching of Flasher signals in production environments, preventing interference between test devices connected to the same lines. By controlling relays via VTSUPPLY, it ensures stable and reliable operation in testing and programming processes. Segger Relay Adapter (8.06.41)

The Segger J-Link USB Isolator (8.07.02) provides isolation up to 3 kV DC and supports USB Full-Speed transmission with a maximum output current of 200 mA. The device is equipped with short-circuit protection and LED indicators for power status and overload.

The Intel FPGA Adapter (formerly J-Link Altera Adapter) connects to the Intel FPGA 10-pin JTAG connector, enabling debugging of FPGA-based MCU cores such as the dual-core Arm Cortex-A9 in Cyclone V devices. on Intel FPGA solutions.

Segger adapter 8.06.28 allows conversion from a 20-pin 0.1" connector to a 10-pin 0.05" Cortex-M type connector with the option of custom pin mapping. A useful solution for integrating programmers and debuggers with devices featuring different pin configurations.

Standard 20-pin 0.1 male connector to provide electrical isolation, Segger

A device that provides electrical isolation between the J-Trace emulator and the ARM board, which protects against electrical interference, especially in systems where the development tools and the application do not share the same ground. It provides 1 kV DC isolation, supports trace frequencies up to 75 MHz, and is compatible with J-Trace V2 and later versions, with a minimum power consumption of 25 µA. Segger J-Trace Isolator (07/08/10)

An advanced tool that enables the integration of J-Link support into your own applications, used in both development environments and custom production tools. Supports debugging, flash programming, and application testing, offering support for Windows, Linux, and macOS, as well as compatibility with many programming languages ​​via a DLL or shared library. Segger J-Link SDK (08.08.06)

Adapter enabling connection of Flasher PRO programmers and other Flasher models to devices with a 10-pin Renesas connector. It is compatible with M16C, M32C, R8C and R32C microcontrollers, providing stable communication and easy integration with older and modern programming systems. Segger Renesas M16C Family 10-Pin Adapter (8.06.40)

10-wire ribbon cable (1.27mm to 2.54mm) for Segger J-Link EDU mini

A 1:1 adapter that allows you to connect a standard 20-pin connector to its 2mm pitch counterpart without any additional configuration. For some models, such as the J-Link PRO, pins 14, 16, 18 and 20 may not be connected to ground, so it is recommended to leave them unconnected on the target hardware. Segger 2mm Adapter (06/08/11)

Xilinx adapter that connects to Xilinx\'s 14-pin, 2mm JTAG connector, providing debugging of MCU cores such as the Arm Cortex-A9 on Xilinx Zynq FPGAs. With its compact design and high signal quality, it is a reliable tool for engineers working with FPGA platforms. Segger Xilinx Adapter (06/08/19)

Adapter that enables JTAG connection between Flasher programmer and target hardware with Power Architecture or PowerPC microcontrollers. Converts 20-pin 0.1\'\' connector to 14-pin JTAG, ensuring compatibility, stability and secure connection. Segger PPC 14-Pin Adapter (06.08.07)

The Segger J-Link Mictor 38 Adapter allows connection to a 38-pin Mictor connector in accordance with the ARM "ETM" specification. The adapter connects the GND and JTAG pins to the 20-pin J-Link, and the trace pins on the Mictor connector are not used.