New products
New products New products
Best sellers
There are 16544 products.
Self-assembly case designed for minicomputers Odroid H3 and Odroid H3+. Equipped with a slot for a network card and two slots for a 2.5" SATA drive. Hardkernel ODROID-H3 Case Type 7
Self-assembly case designed for minicomputers Odroid H3 and Odroid H3+. Equipped with a place for a fan. Hardkernel ODROID-H3 Case Type 2
HAT designed for Raspberry Pi minicomputers with a two-channel RS232 converter. Communication is realized via the SPI interface. The overlay uses a standard 40-pin Raspberry Pi connector. Waveshare 2-CH RS232 HAT
Probe for measuring AC currents up to 1000 A. It works in the range from 10 Hz to 100 kHz, it can be connected to the oscilloscope through the BNC connector. Micsig ACP1000
A set of two magnetic encoders for use with Pololu DC Micro motors. The maximum resolution is 12 pulses per one revolution of the motor shaft. Powered from 2.7V to 18V. Pololu 4761
Expansion board with 4G/3G/2G communication module and GNSS positioning. The kit has pins compatible with Arduino and STM32 Nucleo. DFRobot TEL0124
A round, flexible, pressure sensor that can be used to realize very sensitive force detection. The sensor is durable and designed to detect static and dynamic pressure at high reaction speed. DFRobot SEN0298
Servo equipped with metal gear and analogue feedback. It is supplied with the voltage in the range from 4.8 to 7.2 V. DFRobot SER0044
Miniature, 12V brush DC motor with metal gear with 15.25: 1 ratio. It has a cross section of 10 × 12 mm, and the D-shaped output shaft has a length of 9 mm and a diameter of 3 mm. It also has an extended motor shaft with dimensions of 4.5 × 1 mm. Pololu 4789
This sensor is a carrier/breakout board for ST’s VL6180X proximity and ambient light sensor, which measures the range to a target object up to 20 cm away (or 60 cm with reduced resolution). Pololu 2489
The stepper motor driver with the MP6500 system, allows the bipolar motor to be supplied with a current of up to 2A per phase, without the use of a heat sink. The system can be supplied with voltage in the range 4.5 ... 35V. Polol 2969
LTE Cat 4 module that supports wireless communication over LTE-TDD, LTE-FDD, HSPA+, GSM, GPRS and EDGE technologies. FPC antenna included. Waveshare SIM7600G-H 4G Module
Expansion board based on the Wiznet W5200 Ethernet system. It allows you to easily connect Arduino to an Ethernet network. DFRobot DFR0125
Module with 3 QTR type optocoupler with analog output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 30 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4203
Module with 3 QTRX type optocoupler with RC (digital) output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 30 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4303
The Tic 36v4 USB Multi-Interface High-Power Stepper Motor Controller makes basic control of a stepper motor easy. Pololu 3141
Module with 2 QTR type optocoupler with analog output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 30 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4242
Module with 31 QTR type optocoupler with analog output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 50 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4231