Gravity: Electrochemical Oxygen Sensor - module with an oxygen concentration sensor
ID: 1179237
zł498.61
Tax included
zł405.37 tax excl.
Module with an oxygen concentration sensor in the environment. It allows you to measure the volume of oxygen in the range from 0 to 100%. It communicates via the I2C interface. DFRobot SEN0496
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
Module with an oxygen concentration sensor in the environment. It allows you to measure the oxygen volume in the full range from 0 to 100%. It is characterized by high accuracy and stability of measurements. It has a built-in calibration algorithm, and the sensor probe, based on the principle of electrochemistry, has strong anti-interference properties and a long service life. The module communicates via the I2C interface. Can be widely used in areas such as portable and air quality monitoring devices.
The sensor can be calibrated by the user for more accurate measurements. Calibration manual and sample programs are available on the product page.
Features
- Oxygen detection
- Interface: Gravity I2C
- Measuring range: 0 to 100% by volume
- Response time: ≤5 seconds
- Pressure range: 0.5 to 2 bar
- Service life:> 2 years
- Voltage: 3.3 to 5.5 V
- Working temperature: -20 to 50 ℃
- Operating humidity: 0 to 99% RH (non-condensing)
- Dimensions: 32 x 27 mm
Kit contains
- Gravity module: Electrochemical Oxygen Sensor
- AO2 probe
- Gravity-4pin I2C cable
- Molex 2510 PH2.0 cable 20 cm
1179237
Data sheet
- Interface
- I2C
- Type of sensor
- AO2
- Power supply voltage
- 3,3 - 5 V
- Concentration measurement
- O2
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł109.90
24h
Available quantity: 122
Available
Available
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
zł23.30
24h
Available quantity: 1
Available
Module with an ambient oxygen concentration sensor. The system allows you to measure the oxygen volume in the range up to 25% with a resolution of 0.15%. The module communicates via the I2C interface. DFRobot SEN0322
zł366.85
Delivery date unknown
No product available!
A set of 10 cables, 30 cm long, compliant with the Gravity standard. DFRobot FIT0513
zł30.96
24h
Available quantity: 3
Available
Other products in the same category (16)
Digital gas sensor solution that senses a wide range of Total Volatile Organic Compounds (TVOCs), including equivalent carbon dioxide (eCO2) and metal oxide (MOX) levels, intended for indoor air quality monitoring in personal devices such as watches and phones, but we’ve put it on a breakout board so you can use it as a regular I2C device. SEN-14193
zł193.38
24h
Available quantity: 2
Available
A sensor used to detect pollutants in the air by measuring gases such as hydrogen, ethanol and carbon monoxide. It is used in various areas, such as the food industry, chemical industry, air quality control in laboratories and environmental monitoring. Figaro TGS2600
zł27.34
24h
Available quantity: 8
Available
Air quality sensor module based on the SGP40 system. It communicates via the I2C interface. DFRobot SEN0392
zł82.10
24h
Available quantity: 1
Available
Module with LPG gas concentration sensor (MQ-6) in the range of 200 - 10,000 ppm. The module has an analogue output and a digital output triggered by exceeding the threshold of sensitivity. modMQ-6
zł7.00
6 weeks
No product available!
The MQ-3 sensor allows you to measure the concentration of alcohol vapors. The measuring range of the sensor is in the range of 0.05 mg / L to 10mg / L, and an analogue signal is obtained at the output.
zł8.44
24h
Available quantity: 13
Available
Module with hydrogen sulphide sensor made in MEMS technology. It allows gas detection in the range of 0.5 to 50 ppm and has an analog output. DFRobot SEN0568
zł45.30
24h
Available quantity: 2
Available
Module with a gas concentration sensor MQ9, which enables the detection of carbon monoxide and combustible gases (methane, propane). The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020045
zł55.71
24h
Available quantity: 3
Available
Methane sensor module made in MEMS technology. It allows gas detection in the range of 1 to 10000 ppm and has an analog output. DFRobot SEN0565
zł26.42
Delivery date unknown
No product available!
Available
A sensor that detects the concentration of nitrogen dioxide. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0471
zł817.00
4 weeks
No product available!
Module with an analog MQ4 methane sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0129
zł35.21
24h
Available quantity: 2
Available
I2C BME680 Environmental Sensor is a gas, pressure, temperature and humidity sensor in one MEMS housing. The module is supplied with 3.3-5V, for communication the I2C or SPI interface is used. DFRobot SEN0248
zł104.93
24h
Available quantity: 3
Available
The MQ-9 sensor allows the measurement of gas concentrations such as carbon monoxide, propane and methane. Sensor measuring range: 10 - 10,000 ppm
zł7.07
24h
Available quantity: 10
Available
A sensor that detects the concentration of carbon monoxide. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0466
zł353.87
4 weeks
No product available!
Available
Module with an analog gas sensor. It allows you to measure the concentration of NO, NO2 and H2. DFRobot SEN0441
zł51.72
24h
Available quantity: 3
Available
Module with an oxygen concentration sensor in the environment. It allows you to measure the volume of oxygen in the range from 0 to 100%. It communicates via the I2C interface. DFRobot SEN0496