

A module with a carbon monoxide sensor that uses the latest technology of the microelectromechanical system (MEMS), thanks to which the sensor has compact dimensions, low power consumption, short time of obtaining measurements and quick response. It can qualitatively measure the concentration of carbon monoxide in the range of 5 to 5000 ppm and is suitable for generating leak alarms, e.g. in portable gas detectors. The sensor has an analog output and is supplied with a voltage of 3.3 V to 5 V. Full documentation and sample programs are available on the product page.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Gravity: I2C ADS1115 The 16-Bit ADC Module is an analogue-to-digital converter module for Arduino and Raspberry Pi. This module uses 16-bit ADC ADS1115 and is powered by 3.3 ... 5V. DFRobot DFR0553
Pololu MQ Gas Sensor Carrier
The module with an alcohol sensor (MQ-3), allows you to measure the concentration of ethanol in the air. The module has an analogue output and an output triggered by exceeding the threshold of sensitivity.
Gravity: Analog Infrared CO2 Sensor is a high precision analogue CO2 sensor. It measures CO2 content in the range of 0 ... 5000ppm and is compatible with all devices with ADC function. DFRobot SEN0219
A sensor that detects the concentration of hydrogen sulphide. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0467
No product available!
A sensor that detects the concentration of hydrogen fluoride. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0475
No product available!
Sensor that detects the concentration of chlorine. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0468
No product available!
The MQ-4 sensor allows methane concentration measurement. The measuring range of the sensor reaches up to 10,000 ppm and an analogue signal is obtained at the output.
Module with a sensor of formaldehyde (methanal) concentration in the air. The board is equipped with a Grove connector and communicates via the I2C or UART interface. Seeed Studio 101020972
No product available!
Module with a gas concentration sensor MQ9, which enables the detection of carbon monoxide and combustible gases (methane, propane). The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020045
Module with BME680 sensor for measuring the concentration of volatile organic compounds (VOC), pressure, temperature and humidity. I2C or SPI communication. DFRobot SEN0375
Module with four gas sensors that allow the detection of CO, NO2, alcohol and volatile organic compounds (VOC). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020820
Volatile gas sensor module, including LPG, natural gas, natural gas
Air quality sensor module based on the SGP40 system. It communicates via the I2C interface. DFRobot SEN0392
Air quality sensor module based on the ENS160 system. It communicates via the I2C interface (Gravity connector). DFRobot SEN0514
Module with CO2, temperature and humidity sensor SCD-30. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4867
Carbon monoxide sensor module made in MEMS technology. It allows gas detection in the range of 5 to 5000 ppm and has an analog output. DFRobot SEN0564