Gas Sensor Breakout Board
ID: 200989
5906623438105
zł4.40
Tax included
zł3.58 tax excl.
BOB-08891 - Gas Sensor Breakout Board
BOB-08891 - Gas Sensor Breakout Board
Description:
Simple breakout board for the MQ - 3, MQ - 4, MQ - 6 and MQ - 7 gas sensors. All you need is VCC at 5V, GND, and a resistor to an ADC, that is it.
Note: This is the PCB only
Dimensions: 16.8mm diameter
Download:
200989
Data sheet
- Interface
- Sygnał analogowy
- Type of sensor
- Adapter do czujników serii MQ
- Power supply voltage
- nie dotyczy
- Concentration measurement
- nie dotyczy
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
The MQ-3 sensor allows you to measure the concentration of alcohol vapors. The measuring range of the sensor is in the range of 0.05 mg / L to 10mg / L, and an analogue signal is obtained at the output.
zł8.44
24h
Available quantity: 11
Available
The MQ-4 sensor allows methane concentration measurement. The measuring range of the sensor reaches up to 10,000 ppm and an analogue signal is obtained at the output.
zł4.11
24h
Available quantity: 3
Available
The MQ-6 sensor allows the measurement of LPG, propane and isobutane. The measuring range of the sensor is in the range of 300 - 10.000 ppm, while the output receives an analog signal.
zł6.03
24h
Available quantity: 2
Available
The MQ-7 sensor allows you to measure the concentration of carbon monoxide (carbon monoxide). The measuring range of the sensor is in the range of 10 - 10,000 ppm
zł8.25
24h
Available quantity: 3
Available
Other products in the same category (16)
Module with CO2, temperature and humidity sensor SCD-41. Equipped with a Qwiic/STEMMA QT connector, it communicates via the I2C interface. Pimoroni PIM587
zł400.32
24h
Available quantity: 1
Available
A sensor that detects the oxygen concentration. Equipped with a factory calibrated probe. It communicates via the UART interface or the analog output. Seeed Studio 101020912
zł539.04
4 weeks
No product available!
Module with a sensor of formaldehyde (methanal) concentration in the air. The board is equipped with a Grove connector and communicates via the I2C or UART interface. Seeed Studio 101020972
zł356.05
4 weeks
No product available!
Module with a BME688 sensor for measuring gas concentration, pressure, temperature and humidity. I2C or SPI communication. SparkFun SEN-19096
zł196.21
24h
Available quantity: 3
Available
Module with an oxygen concentration sensor in the environment. It allows you to measure the volume of oxygen in the range from 0 to 100%. It communicates via the I2C interface. DFRobot SEN0496
zł498.61
4 weeks
No product available!
Module with ENS160 gas sensor for measuring the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via the I2C or SPI interface. Adafruit 5606
zł129.42
24h
Available quantity: 1
Available
Module with an analog MQ2 gas sensor. It enables the detection of LPG, butane, propane, methane, alcohol, hydrogen and smoke. It is powered with the voltage of 5 V and has an analog output
zł10.34
24h
Available quantity: 9
Available
Module with the MQ3 analog alcohol sensor. It allows you to detect gas and build a simple breathalyzer. The module is powered by 5 V and has an analog output
zł14.62
24h
Available quantity: 11
Available
ENS160 gas sensor module to measure the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via an I2C or SPI interface. SparkFun SEN-20844
zł119.84
24h
Available quantity: 3
Available
A sensor used to detect pollutants in the air by measuring gases such as hydrogen, ethanol and carbon monoxide. It is used in various areas, such as the food industry, chemical industry, air quality control in laboratories and environmental monitoring. Figaro TGS2600
zł25.72
4 weeks
No product available!
A sensor used to detect air pollutants by measuring VOCs and gases such as ammonia or hydrogen sulfide. It is used in various areas, such as the food industry, chemical industry, air quality control in laboratories and environmental monitoring. Figaro TGS2602
zł31.33
24h
Available quantity: 14
Available
SCD41 CO2, temperature and humidity sensor module. Equipped with a Gravity connector, it communicates via an I2C interface. DFRobot SEN0536
zł192.70
4 weeks
No product available!
The SCD-41 CO2, temperature and humidity sensor module provides high accuracy readings. It is equipped with a Qwiic connector and communicates via an I2C interface. SparkFun SEN-22396
zł432.23
24h
Available quantity: 1
Available
The SCD-40 CO2, temperature and humidity sensor module provides high accuracy readings. It is equipped with a Qwiic connector and communicates via an I2C interface. SparkFun SEN-22395
zł484.35
24h
Available quantity: 1
Available
Carbon monoxide sensor module made in MEMS technology. It allows gas detection in the range of 5 to 5000 ppm and has an analog output. DFRobot SEN0564
zł23.27
24h
Available quantity: 3
Available
Module with hydrogen sulphide sensor made in MEMS technology. It allows gas detection in the range of 0.5 to 50 ppm and has an analog output. DFRobot SEN0568
zł41.38
24h
Available quantity: 1
Available
BOB-08891 - Gas Sensor Breakout Board