![Main view Main view](https://kamami.pl/79014-large_default/dev-12049-lilypad-arduino-usb-atmega32u4-board.jpg)
![Main view Main view](https://kamami.pl/79014-large_default/dev-12049-lilypad-arduino-usb-atmega32u4-board.jpg)
zł113.01 tax excl.
Microcontroller board controlled by ATmega32U4 with Arduino bootloader. Due to the dimensions and openings, it is perfect for electronic components sewn into clothes. It has a built-in JST connector with a charging circuit and a switch and is programmed via a micro USB connector. SparkFun DEV-12049
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
LilyPad Arduino USB is a microcontroller board controlled by ATmega32U4 with Arduino bootloader. Due to the dimensions and openings, it is perfect for electronic components sewn into clothes. It has a built-in JST connector with a charging circuit and a switch and is programmed via a micro USB connector. The module has eleven pads for connecting components with a conductive thread. Two are reserved for powering LilyPad sensors and accessory boards, and nine are input/output (I/O). Markings in the form of a label with the name and pin number make it easy to identify which pin of the ATmega32U4 is not connected. Full documentation is available on the product page.
DEV-10867 - Conductive Thread Bobbin - 30ft (Stainless Steel)
Pro Micro is similar to Pro Mini Arduino compatible board, main difference is that Pro Micro uses ATmega32u4 with builtin USB connectivity. Sparkfun DEV – 12587
No product available!
Kit with LEDs, battery, needles and conductive thread that allows you to sew LED lighting into clothes. SparkFun DEV-11590
Knit conductive 100% silver fabric with resistance of less than 1 ohm per foot in any direction across the textile. Great for use with FLORA. 20 cm x 20 cm piece. Adafruit 1167
Adafruit 1059 - Flora Wearable Ultimate GPS Module
Adafruit 603 - Stainless Thin Conductive Yarn / Thick Conductive Thread - 35 ft
A miniature module with a programmed AVR Attiny85 microcontroller, equipped with 8 KB of Flash memory, 4 digital pins, analog input and 2 PWM channels. By connecting the LEDs to the digital outputs of the module, interesting lighting effects can be obtained. SparkFun DEV-10899
Woven conductive fabric silver-plated nylon with resistance of less than 1 ohm per foot in any direction across the textile. Great for use with FLORA. 20 cm x 20 cm piece. Adafruit 1168
Power module designed to work with LilyPad boards. It is equipped with a switch and a CR2032 battery socket. SparkFun DEV-13883
DEV-10867 - Conductive Thread Bobbin - 30ft (Stainless Steel)
The LilyPad series module is designed for prototyping interactive e-textiles. It consists of a board with a SAMD11 microcontroller and a CR2032 battery socket, LEDs, a light sensor and a button. SparkFun DEV-14063
XBee adapter with pads with holes for sewing the module to clothes and fabrics. SparkFun DEV-12921
GEMMA M0 is an intelligent clothing controller from Adafruit. In relation to the classic GEMMA board, it was equipped with a 32-bit ATSAMD21E18 microcontroller (based on Cortex M0 +). It has GPIO pins, RGB DotStar diode. The board can be powered by a 3.7 V Li-Ion battery (JST connector). Adafruit 3501
No product available!
TCS34725 has RGB and Clear light sensing elements. An IR blocking filter, integrated on-chip and localized to the color sensing photodiodes, minimizes the IR spectral component of the incoming light and allows color measurements to be made accurately. Adafruit 1356
Microcontroller board controlled by ATmega32U4 with Arduino bootloader. Due to its dimensions and holes, it will be excellent for electronic components sewn into clothing. It has a built-in JST connector with charging circuit and on/off switch and is programmable via micro USB. SparkFun DEV-14631
No product available!
A miniature module with a LiPo battery charger with a capacity of 500 mA. SparkFun DEV-11893
Microcontroller board controlled by ATmega32U4 with Arduino bootloader. Due to the dimensions and openings, it is perfect for electronic components sewn into clothes. It has a built-in JST connector with a charging circuit and a switch and is programmed via a micro USB connector. SparkFun DEV-12049