![SparkFun Spectral Sensor AS7263 NIR - moduł z czujnikiem Spektrum dla światła widzialnego oraz NIR SparkFun Spectral Sensor AS7263 NIR - moduł z czujnikiem Spektrum dla światła widzialnego oraz NIR](https://kamami.pl/30535-large_default/sparkfun-spectral-sensor-breakout-as7263-nir-qwiic.jpg)
![SparkFun Spectral Sensor AS7263 NIR - moduł z czujnikiem Spektrum dla światła widzialnego oraz NIR SparkFun Spectral Sensor AS7263 NIR - moduł z czujnikiem Spektrum dla światła widzialnego oraz NIR](https://kamami.pl/30535-large_default/sparkfun-spectral-sensor-breakout-as7263-nir-qwiic.jpg)
zł114.28 tax excl.
SEN-14351
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
The SparkFun AS7263 Near Infrared (NIR) Spectral Sensor Breakout brings spectroscopy to the palm of your hand, making it easier than ever to measure and characterize how different materials absorb and reflect different wavelengths of light. The AS7263 Breakout is unique in its ability to communicate by both an I2C interface and serial interface using AT commands. Hookup is easy, thanks to the Qwiic connectors attached to the board — simply plug one end of the Qwiic cable into the breakout and the other into one of the Qwiic shields, then stack the board on a development board. You’ll be ready to upload a sketch to start taking spectroscopy measurements in no time.
The AS7263 spectrometer detects wavelengths in the visible range at 610, 680, 730, 760, 810 and 860nm of light, each with 20nm of full-width half-max detection. The board also has multiple ways for you to illuminate objects that you will try to measure for a more accurate spectroscopy reading. There is an onboard LED that has been picked out specifically for this task, as well as two pins to solder your own LED into.
The SparkFun Qwiic Connect System is an ecosystem of I2C sensors, actuators, shields and cables that make prototyping faster and less prone to error. All Qwiic-enabled boards use a common 1mm pitch, 4-pin JST connector. This reduces the amount of required PCB space, and polarized connections mean you can’t hook it up wrong.
SEN-14348
No product available!
SEN-14347
No product available!
Module with light intensity sensor LTR-303. It offers a measuring range from 1 to 65535 lux and a 16-bit resolution. Communication takes place using I2C. Adafruit 5610
Module with a light sensor and a proximity sensor up to 5 cm. It allows you to read the illuminance from 0.01 to 64000 lux and communicates via the I2C interface. Pimoroni PIM413
ireless sensor with LoRaWAN network communication. Dedicated to industrial long-distance data acquisition with a wide light intensity measurement range from 0 to 160000 Lux. Seeed Studio 114992868
No product available!
Sensor for detecting the distance, intensity and frequency of lightning within a radius of 40 km. The module enables weather enthusiasts to measure local storm data. SparkFun SEN-15441
Module with a UV light sensor LTR390-UV. It allows you to measure the intensity of ultraviolet radiation and visible light. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4831
LTR390-UV UV light sensor module. Allows measurement of ultraviolet and visible light intensity. Equipped with a Gravity connector, it communicates via an I2C or UART interface. DFRobot SEN0540
DFRobot Gravity analog light intensity module for Arduino and Raspberry Pi. DFRobot DFR0026
Module with color sensor TCS34725FN. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020341
A module with a spectrum sensor that operates in the visible light range (450-650 nm). It allows you to measure and characterize a light source or check how the tested surface absorbs or reflects light at specific wavelengths. Pimoroni PIM412
Module with 11-channel AS7341 sensor that allows to detect light in different wavelength ranges (color detection). It communicates via the I2C interface. Waveshare AS7341 Spectral Color Sensor
TCS34725 RGB Color Sensor is a color sensor TCS34725 controlled by the I2C interface. It is powered by voltage in the range of 3.3 ... 5V and is intended for Arduino-compatible boards. DFRobot SEN0212
Module with light sensor - LS06-S phototransistor. The board is equipped with a Grove connector and has an analog output. Seeed Studio 101020132
Module with a light intensity sensor LTR-329. It offers a measuring range from 1 to 65535 lux and a 16-bit resolution. Communication takes place using I2C. Adafruit 5591
Heart rate monitor module based on the popular MAX30101 chip. The board is equipped with connectors compliant with the Qwiic standard. SparkFun SEN-16474
No product available!
Module with a light intensity sensor BH1750FVI dedicated to the M5StickC sets. It communicates via the I2C interface. M5Stack U134
SEN-14351