MOIP1000P - isolated 1GHz fiber optic probe for Micsig oscilloscopes
ID: 1187019
zł112,990.00
Tax included
zł91,861.79 tax excl.
Insulated fiber optic probe with a measuring range up to 2500 V. It works in the band up to 1 GHz, it can be connected to the oscilloscope via the BNC connector. Comes with a 10X attenuation tip. Micsig MOIP1000P
Description
An isolated fiber optic probe that works in the frequency band up to 1 GHz. It uses a standard BNC interface and can be connected to an oscilloscope or multimeter. Utilizing SigOFIT optical isolation technology, it offers high accuracy and excellent suppression of oscillations caused by high-frequency common-mode noise.
The probe has excellent amplitude-frequency characteristics and the DC gain accuracy is less than 1%. The maximum noise floor in this range is 1.41 mVrms and the zero drift is less than 500 μV. It is an excellent choice for the study of third generation semiconductors and devices based on SiC and GaN. The probe test leads are short and have an input capacitance of less than 3 pF when transmitted via coaxial cable, allowing for very safe testing.
Unlike traditional differential probes that can only test high-voltage signals, the SigOFIT can be used with a variety of tips to test differential mode signals from ±1.25 V to ±2500 V, achieving full output range and very high signal to ratio noise. It will be used in industry, automotive electronics, when servicing power supplies and inverters. It is dedicated to Micsig devices.
Features
- Bandwidth: 1GHz
- Rise time: 350 ps
- SMA input impedance: 1MΩ || 10pF
- Output voltage: ±1.25V
- Measuring ranges:
- 1X: ±1.25V
- 20X: ±25V
- 50X: ±62.5V
- 1000X: ±1250V
- 2000X: ±2500V
- Noise: <1.41mVrms
- Signal Delay: ＜15.42ns
- DC Gain Accuracy: 1%
- Common mode voltage range: 60kVpk
- Power: DC 5V, USB Type-C
- Cord length: 2m
Kit contains
- Probe
- USB Type-C cable
- Probe holder
- 25W USB charger
- 5 x MCX adapter with 2.54mm pitch
- 5 x MCX adapter with 5.05mm pitch
- MCX coaxial cable
- 20X and 1000X probe tip
- Case
1187019
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Test probe tip with 20X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 800 MHz and 1 GHz frequency band. Micsig OP20-1G
zł6,599.00
Delivery date unknown
No product available!
Test probe tip with 50X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 800 MHz and 1 GHz frequency band. Micsig OP50-1G
zł6,599.00
Delivery date unknown
No product available!
Test probe tip with 1000X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 800 MHz and 1 GHz frequency band. Micsig OP1000-1G
zł6,599.00
Delivery date unknown
No product available!
Test probe tip with 2000X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 800 MHz and 1 GHz frequency band. Micsig OP2000-1G
zł10,516.50
Delivery date unknown
No product available!
Other products in the same category (16)
Probe for measuring direct and alternating current up to 30 A. Works in the band up to 50 MHz, can be connected to the oscilloscope through the BNC connector. Powered by USB. Micsig CP503B
zł3,431.45
4 weeks
No product available!
The Hantek PP-300 is an oscilloscope probe with a bandwidth of 300 MHz, designed for precise measurement of high-frequency signals. It is compatible with a wide range of digital and analog oscilloscopes and features a switchable attenuation setting between 1× and 10×, allowing flexible adaptation to various applications. Thanks to its ergonomic design and robust construction, the probe offers user comfort and durability for everyday use in laboratory environments.
zł134.54
24h
Available quantity: 10
Available
6-wire test leads that allow the oscilloscope to be connected to various components in the engine compartment without stripping or puncturing the insulation and without risking damage to the connectors. Hantek HT306-2.8mm
zł47.92
24h
Available quantity: 10
Available
Probe for measuring direct and alternating current up to 100 A. It works in the 2,5 MHz band, it can be connected to the oscilloscope through the BNC connector. Powered by USB. Micsig CP2100B
zł2,143.69
4 weeks
No product available!
BNC connector cable (adapter) to the "Alligator clip" connector. It allows you to conveniently connect the device, e.g. to an oscilloscope. Digilent (240-134)
zł52.64
24h
Available quantity: 3
Available
Test probe tip with 50X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 350 MHz and 500 MHz frequency bands. Micsig OP50-5
zł4,598.99
4 weeks
No product available!
Insulated fiber optic probe with a measuring range up to 2500 V. It works in the band up to 500 MHz, it can be connected to the oscilloscope via the BNC connector. Comes with a 10X attenuation tip. Micsig MOIP500P
zł74,999.00
4 weeks
No product available!
A 20:1 signal attenuator designed to assist in measuring automotive performance, including measuring fuel injector and primary ignition runs. Hantek HT201
zł51.99
24h
Available quantity: 3
Available
The Micsig P300 oscilloscope probe with a BNC connector offers a bandwidth of 300 MHz and a maximum input voltage of 600 V, enabling precise measurements of high-frequency and high-voltage signals. Its high input impedance minimizes impact on the circuit under test, ensuring measurement accuracy. The standard BNC connector ensures compatibility with most oscilloscopes, making it a versatile tool for laboratories and engineering applications.
zł201.82
4 weeks
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is perfect for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP600XS
zł4,059.00
4 weeks
No product available!
A probe for measuring AC and DC currents up to 65 A. It operates in a bandwidth of up to 20 kHz and can be connected to an oscilloscope via a BNC connector. Hantek CC-65
zł357.17
4 weeks
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is ideal for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP6000XS
zł4,551.00
4 weeks
No product available!
Probe for measuring direct and alternating current up to 30 A. Works in the band up to 100 MHz, can be connected to the oscilloscope through the BNC connector. Powered by USB. Micsig CP1003B
zł3,427.73
4 weeks
No product available!
Oscilloscope Probes (pair). 460-004
zł136.75
24h
Available quantity: 3
Available
Micsig DP series differential probe based on advanced SigOFIT technology. It offers a frequency band of 100 MHz and the ability to measure voltage up to 1500 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig DP1500
zł1,151.14
4 weeks
No product available!
Test probe tip with 20X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 800 MHz and 1 GHz frequency band. Micsig OP20-1G
zł6,599.00
4 weeks
No product available!
Insulated fiber optic probe with a measuring range up to 2500 V. It works in the band up to 1 GHz, it can be connected to the oscilloscope via the BNC connector. Comes with a 10X attenuation tip. Micsig MOIP1000P