New products
New products New products
zł9,349.00
4 weeks
zł173.58
Delivery date unknown
Qwiic Quad Relay - 4-channel module with relays
ID: 581507
5906623420490
zł170.59
Tax included
zł138.69 tax excl.
Module with 4 relays JZC-11F with a load of 5A. It enables switching devices with high power using a microcontroller. I2C communication. SparkFun COM-16566
Description
Module with 4 relays JZC-11F with a load of 5 A. It enables switching devices with high power using a microcontroller. The module is based on the ATtiny84 system, which carries out the commands for switching four relays. The I2C address is configurable by software (one of 100 available addresses can be selected). The module is powered by the DC connector with the voltage in the range of 7 to 12 V or 5 V after switching the jumper. The board is equipped with a number of security features. The product page features a guide and an Arduino library.
Features
- Four JZC-11F relays (5A, 250VAC, 30VDC)
- Each relay has its own LED and label for easy identification
- Security features: ground insulation, air gap, bold tracks
- ATtiny84A microcontroller
- I2C communication
- I2C address: 0x6D (default), 0x6C (jumper)
- Software configurable I2C address
- All commands are listed in the sample code.
- Screw terminals for 26-14 AWG wire
- 7 to 12 V power supply (via DC connector) or 5 V power supply with bypass jumper
- Current consumption up to 250 mA
581507
Data sheet
- Output current
- 5A
- Number of channels
- 4
- Executive element
- Przekaźnik
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Available
Available
Flexible 4-core cable, 200 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17258
zł12.96
24h
Available quantity: 6
Available
Other products in the same category (16)
The module with 4 relays is designed to work with Arduino. It allows you to control devices with operating parameters up to 250VAC/7A or 30VDC/10A. Seeed Studio 103030009
zł108.41
24h
Available quantity: 1
Available
Industrial module with 4 relays with a load of up to 10 A. It uses the Modbus RTU protocol and the RS485 or RS232 communication interface. DFRobot FIT0827
zł155.02
4 weeks
No product available!
Module with 32 24 V relays with a maximum switching current of 7 A. It communicates via the USB interface. Numato Lab RL320001-24
zł1,238.22
3 weeks
No product available!
Compact module with MOSFET IRF520 24V/5A transistor.
zł3.19
24h
Available quantity: 26
Available
The remotely controlled modulation module MOD-34 / AZ allows wireless load control with up to 10 A current consumption via a relay. It does not contain nRF24l01.
zł51.94
24h
Available quantity: 1
Available
The module with the HLS8-T73 relay with a load up to 5 A. The board is equipped with a Grove connector and is controlled by a digital input. Seeed Studio 103020005
zł13.80
24h
Available quantity: 7
Available
The module is equipped with eight 10A / 250VAC relays controlled independently via a serial bus (UART) or from a PC (through a microUSB connector). The NO / NC contacts of the relays have been led to the ARK screw terminals. The board recommended for use with Arduino enables the control of eight relays using only two microcontroller lines. ICSTATION ICSE014A
zł50.41
24h
Available quantity: 2
Available
Module with 4 relays with a maximum switching current of 7 A. It communicates via the USB interface. Numato Lab RL40001
zł234.59
3 weeks
No product available!
Programmable time module with relay, allows you to set the time and manner of relay reaction on the trigger signal, has a built-in LED display. It can be supplied with voltage from the range of 6 - 30VDC or using the microUSB connector
zł9.84
4 weeks
No product available!
Industrial module with 8 relays. It communicates via RS485 interface and supports Modbus RTU protocol. Waveshare Modbus RTU Relay (EN)
zł122.56
4 weeks
No product available!
Module with eight 240V/2A relays controlled by 5V with a fuse triggered by a high state. modSSR-8CH-H
zł53.65
4 weeks
No product available!
This module allows independent control of two Omron G5LE-14-DC5 SPDT relays, supporting currents up to 10A. Thanks to built-in BSS138K MOSFETs, it can be controlled directly from 3.3V or 5V development boards such as Arduino or Raspberry Pi. Each channel is equipped with an LED to indicate relay activation and 5mm screw terminals for convenient circuit connection. Pololu 5665
zł64.30
24h
Available quantity: 2
Available
Module with 8 relays 12 V with a maximum switching current of 7 A. Communicates via the USB interface. Numato Lab RL80001
zł441.59
3 weeks
No product available!
Module with 8 relays and 10 analog inputs. Communicates via the WiFi wireless interface. Numato Lab WFRL80001
zł1,080.86
3 weeks
No product available!
The module is equipped with four 10A / 250VAC relays controlled independently via a serial bus (UART) or from a PC (through a microUSB connector). The NO / NC contacts of the relays have been led to the ARK screw terminals. ICSTATION ICSE012A
zł44.58
24h
Available quantity: 1
Available
Industrial module with 32 relays. It uses communication via the RS485 interface and supports the Modbus RTU protocol. Waveshare Modbus RTU Relay 32CH
zł277.77
24h
Available quantity: 11
Available
Module with 4 relays JZC-11F with a load of 5A. It enables switching devices with high power using a microcontroller. I2C communication. SparkFun COM-16566