Dual MC33926 Motor Driver Carrier - two-channel DC motor driver with MC33926
ID: 195608
zł232.97
Tax included
zł189.41 tax excl.
Dual MC33926 Motor Driver CarrierTwo-channel DC motor controller with voltage from 5 V to 28 V, power consumption up to 3 A per channel. Controlled by PWM signal. Pololu 1213
Description
Two-channel DC motor controller with voltage from 5 V to 28 V, allows the motor to be controlled with a current of up to 3 A per channel (5 A at the peak). The module is based on two MC33926 circuits. MC33926 supports ultrasonic (up to 20 kHz) pulse width modulation (PWM) of motor output voltage, which eliminates audible switching sounds caused by PWM speed control, and the current feedback circuit for each motor outputs an analog voltage to the appropriate FB pin proportional to the output current. MC33926 has protection against low voltage, overload and overheating. Some events are indicated by status flags (SF).
Typically, five I / O lines are used to connect each channel of the motor controller with the microcontroller: two input lines, IN1 and IN2, for direction control, one of the shutdown lines, D1 or D2, for PWM speed control, current output signal, FB, for monitoring the motor current consumption (connected to the analog-to-digital converter input) and SF status flag, for monitoring the motor controller errors.
Excellent general purpose motor controller for medium DC motors and differential drive robots.
Features
- Driver: MC33926
- Number of channels: 2
- Motor power supply: 5 to 28 V
- Current capacity: 3 A (5 A peak) per channel
- Maximum PWM frequency: 20 kHz
- Current measurement: 0.525 V / A
- Power supply for the logic part: 2.5 to 5.5 V
- Dimensions: 28 x 45.7 mm
- Weight: 7 g
Kit contains
- Two-channel MC33926 controller module
- 25pin goldpin straight connector
- 3 x Screw connectors
195608
Data sheet
- Output current
- 3A
- Number of channels
- 2
- Supply voltage min
- 5 V
- Supply voltages max
- 28 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Cables for evaluation boards, set of 10 pcs., blue colour
zł5.20
24h
Available quantity: 21
Available
Cables for evaluation boards, set of 10 pcs., red colour
zł5.20
Delivery date unknown
No product available!
Cables for evaluation boards, set of 10 pcs., green colour
zł5.46
24h
Available quantity: 315
Available
Cables for evaluation boards, set of 10 pcs., yellow colour
zł5.61
24h
Available quantity: 36
Available
Cables for evaluation boards, set of 10 pcs., white colour
zł6.06
24h
Available quantity: 16
Available
Pololu Dual MC33926 Motor Driver Shield for Arduino
zł197.80
24h
Available quantity: 2
Available
MC33926 Motor Driver Carrier
zł102.19
Delivery date unknown
No product available!
This add-on board enables a Raspberry Pi B+, Pi A+, Pi 2 or Pi 3 to drive a pair of brushed DC motors. Its dual MC33926 motor drivers operate from 5 V to 28 V and can deliver a continuous 3 A (5 A peak) per motor. The default pin mappings make it easy to get started using our provided software, but the board also exposes most of the driver chips’ I/O pins for more specialized applications.
zł199.00
Delivery date unknown
No product available!
Other products in the same category (16)
The DC motor driver module enables the motor to be controlled using a PWM signal with several supply voltages (3V, 6V, 12V, 24V and 35V) and a maximum continuous current of 5A.
zł7.81
24h
Available quantity: 12
Available
Stepper motor driver based on TB67S249FTG. It allows you to control a stepper motor with voltage from 10 to 47V, with a maximum current of 1.8A. The controller can be controlled using: USB, Serial TTL, I2C, RC (PWM modeling), analog input or quadrature encoder. Pololu 3138
zł252.80
24h
Available quantity: 1
Available
STSPIN220 stepper motor driver module with a low voltage range of 1.8 ... 10V and 1.1A working current. The controller allows you to control the motor motion up to 9 different resolutions (up to 1/256 steps). Pololu 2876
zł37.80
24h
Available quantity: 2
Available
Dual DC motor controller designed for Raspberry Pi, which enables the engine to be supplied with voltage in the 4.5-28V range and power consumption in continuous operation of 2.6A (5A in peak) of two DC motors. Pololu 2762
zł155.91
24h
Available quantity: 1
Available
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 30 V voltage range and is efficient enough to deliver a continuous 25 A without a heat sink.
zł286.68
4 weeks
No product available!
DC motor driver that allows you to control the movement of three drives using the I2C interface. Connectors for self-assembly. Pololu 5034
zł210.27
24h
Available quantity: 1
Available
Module with a stepper motor driver based on the DRV8434A system. It allows the bipolar motor to be supplied with current up to 1.2 A per phase and with a voltage from 4.5 V to 45 V. Communication via the SPI interface. Pololu 3768
zł54.74
4 weeks
No product available!
ESC RC controller module with FlySky receiver designed for two brush motors with a supply voltage from 2.5 to 5 V and a current consumption of 2 A
zł146.80
4 weeks
No product available!
An advanced speed controller designed to power three-phase brushless motors in various applications, such as driving robots, walking robots or gimbals. Supports input voltage range from 12V to 56V. Maximum constant current is 60A. Makerbase ODrive-S
zł288.03
24h
Available quantity: 4
Available
Module with DC motor driver DRV8256E. It can work with motors supplied with the voltage from 4.5 to 48 V and the current consumption up to 1.9 A. Pololu 4038
zł72.59
24h
Available quantity: 2
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5050
zł305.08
4 weeks
No product available!
This powerful motor controller makes closed-loop speed or position (but not both!) control of a brushed DC motor easy, with quick configuration over USB using our free software. It supports five control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), and hobby radio control (RC).
zł450.07
24h
Available quantity: 1
Available
Raspberry Pi Expansion Board, DC Motor / Stepper Motor Driver
zł115.66
24h
Available quantity: 2
Available
A single-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with connectors for assembly. Pololu 5077
zł59.86
24h
Available quantity: 2
Available
DC motor driver with voltage 6.5..30V and maximum continuous current 27A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3148
zł629.10
4 weeks
No product available!
Dual MAX14870 Motor Driver is a dual DC motor controller compatible with the Arduino standard that allows you to control two DC motors with 4.5 ... 36V continuous current of 1.7A. Polol 2519
zł134.43
24h
Available quantity: 2
Available
Dual MC33926 Motor Driver CarrierTwo-channel DC motor controller with voltage from 5 V to 28 V, power consumption up to 3 A per channel. Controlled by PWM signal. Pololu 1213