This pressure sensor from Freescale is a great low-cost sensing solution for measuring barometric pressure. At 1.5 hPa resolution, it's not as precise as our favorite pressure sensor, the BMP085, which has up to 0.03 hPa resolution so we don't suggest it as a precision altimeter. However, it's great for basic barometric pressure sensing. The sensor is soldered onto a PCB with 10K pull-up resistors on the I2C pins.
This chip is good for use with power and logic voltages ranging from 2.4V to 5.5V so you can use it with your 3V or 5V microcontroller. There's a basic temperature sensor inside but there's no specifications in the datasheet so we're not sure how accurate it is.
Using the sensor is easy. For example, if you're using an Arduino, simply connect the VDD pin to the 5V voltage pin, GND to ground, SCL to I2C Clock (Analog 5 on an UNO) and SDA to I2C Data (Analog 4 on an UNO). Then download our MPL115A2 Arduino library and example code for temperature, pressure and basic altitude calculation. Install the library, and load the example sketch. Immediately you'll have the temperature, pressure and altitude data printed in the serial console.
Data sheet
Manufacturer
Responsible person
Pressure sensor module with I2C interface (MPL115A2)
A set of 40 female-female connection cables, in various colors, 17 cm long. CAB_F-F (Rainbow-40-17)
KAmodLPS25HB is a module that allows the measurement of atmospheric pressure in the range of 260-1260hPa with a resolution of 0.01hPa, and thanks to the embedded regulator and voltage translator levels, it can be successfully used in systems supplied with a voltage of 2.5 - 5.5 V.
KAmodLPS331 is a module that allows the measurement of atmospheric pressure in the range of 260 - 1260 hPa with a resolution of 0.02 hPa. Supply voltage 2.5 - 5.5 V,
The GY-BMP280 is an atmospheric pressure sensor module. It allows measurement in the range of 300 ... 1100 hPa with an accuracy of 1 hPa. The sensor uses I2C or SPI bus
No product available!
Kit with MPX5700AP pressure sensor, syringe and tube. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 110020248
No product available!
Module with a pressure sensor with high accuracy HP206C. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020068
Module with a BME680 sensor that allows you to measure temperature, humidity, pressure and gas detection. The board is equipped with a Grove connector and communicates via I2C and SPI. Seeed Studio 101020513
Module with BME680 sensor for measuring the concentration of volatile organic compounds (VOC), pressure, temperature and humidity. I2C or SPI communication. DFRobot SEN0375
Integrated BME688 gas, pressure, temperature and humidity sensor in one MEMS housing. The system can be supplied with the voltage of 3.3 V and is equipped with an I2C communication interface. BME688 Breakout Board
Module with pressure and temperature sensor BMP280. It allows to read the atmospheric pressure in the range from 300 to 1100 hPa and communicates via the I2C interface. Pimoroni PIM411
Module with pressure, temperature and humidity sensor BME280. It allows to read the atmospheric pressure in the range from 300 to 1100 hPa and communicates via the I2C interface. Pimoroni PIM472
Module with BME680 sensor to measure the concentration of volatile organic compounds, pressure, temperature and humidity. It communicates via the I2C interface. Pimoroni PIM357
Module with digital barometer BMP390. It enables pressure measurement from 300 to 1250 hPa and temperature from -40℃ to 85℃. Communicates via I2C or SPI. Adafruit 4816
No product available!
Module with integrated BME688 gas, pressure, temperature and humidity sensor placed in one MEMS housing. It is equipped with an I2C interface. Adafruit 5046
Module with BME680 for measuring the concentration of VOC, pressure, temperature and humidity. Equipped with a STEMMA QT connector, it communicates via I2C or SPI. Adafruit 3660
Module with digital barometer BMP388. It measures pressure in the range from 300 to 1250 hPa and communicates via I2C or SPI. Adafruit 3966
Module with a digital barometer LPS22. It enables pressure measurement in the range from 260 to 1260 hPa and communicates via I2C or SPI. Adafruit 4633
Module with waterproof barometer LPS33HW. It enables pressure measurement in the range from 260 to 1260 hPa and communicates via I2C or SPI. Adafruit 4414
Module with a pressure, temperature and humidity sensor based on the MS8607. Equipped with a STEMMA QT connector, it communicates via the I2C. Adafruit 4716
Module with an absolute pressure sensor LPS25HB. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4530
1.5 hPa resolution pressure sensor from Freescale. The sensor is soldered onto a PCB with 10K pull-up resistors on the I2C pins. Adafruit 992