Bosch has stepped up their game with their new BME280 sensor, an environmental sensor with temperature, barometric pressure and humidity! This sensor is great for all sorts of weather/environmental sensing and can even be used in both I2C and SPI!
This precision sensor from Bosch is the best low-cost sensing solution for measuring humidity with ±3% accuracy, barometric pressure with ±1 hPa absolute accuraccy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude, and the pressure measurements are so good, you can also use it as an altimeter with ±1 meter or better accuracy!
The BME280 is the next-generation of sensors from Bosch, and is the upgrade to the BMP085/BMP180/BMP183 - with a low altitude noise of 0.25m and the same fast conversion time. It has the same specifications, but can use either I2C or SPI. For simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI.
Nice sensor right? So we made it easy for you to get right into your next project. The surface-mount sensor is soldered onto a PCB and comes with a 3.3V regulator and level shifting so you can use it with a 3V or 5V logic microcontroller without worry.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
The BME280 integrated circuit is a sensor of atmospheric conditions (pressure, humidity, temperature) in the SMD casing (2.5mmx2.5mm). The sensor has very low power consumption (average 3.6uA) and has an I2C / SPI bus. The Bosch Sensortec system
No product available!
BME280 integrates onboard temperature sensor, humidity sensor and barometer. It provides both SPI and I2C interfaces; and can be widely used in environmental monitoring, story height measurement and Internet of Things (IoT) control and so on. SEN0236
Module with pressure and temperature sensor BMP280. It allows to read the atmospheric pressure in the range from 300 to 1100 hPa and communicates via the I2C interface. Pimoroni PIM411
Module with BME680 sensor for measuring the concentration of volatile organic compounds (VOC), pressure, temperature and humidity. I2C or SPI communication. DFRobot SEN0375
Module with a pressure sensor with high accuracy HP206C. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020068
Module with BME280 environmental sensor. It allows you to measure temperature, humidity and pressure. The sensor is equipped with two communication interfaces: SPI and I2C. SparkFun SEN-13905
Module with digital barometer BMP581. It enables pressure measurement in the range from 300 to 1250 hPa with an accuracy of ± 5 Pa and communicates via I2C or SPI. SparkFun SEN-20170
Module with digital barometer ICP-10111. The system enables pressure measurement in the range from 300 to 1100 hPa with an accuracy of 1 Pa. DFRobot SEN0517
LPS35HW waterproof barometer module. It can measure pressure from 260 to 1260 hPa and communicates via I2C or SPI. Adafruit 4258
Module with digital barometer BMP390. It enables pressure measurement from 300 to 1250 hPa and temperature from -40℃ to 85℃. Communicates via I2C or SPI. Adafruit 4816
Water pressure sensor with 3-pin Gravity interface. It enables the measurement of liquid pressure in the range from 0 to 1.6 MPa. It is supplied with the voltage of 5 V and has a linear output voltage from 0.5 to 4.5 V. DFRobot SEN0257
Module with an absolute pressure sensor LPS25HB. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4530
Module with digital barometer ICP-10111. The system enables pressure measurement in the range from 300 to 1100 hPa with an accuracy of 1 Pa. DFRobot SEN0516
KAmodMPL3115A2 is a module with an atmospheric pressure sensor MPL3115A2 from NXP. Sensor allows to make a measurement in the range of 200...1100hPa (20...110kPa). Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMPL3115A2
KAmod BMP390 contains a precise BMP390 sensor manufactured by Bosch Sensortec, enabling the measurement of atmospheric pressure and temperature. All key signals of the miniature BMP390 sensor are routed on the module board, facilitating its use in modular applications. Communication is carried out via SPI or I2C interfaces equipped with voltage level translation circuits.
Module with digital barometer BMP388. The system measures pressure in the range from 300 to 1250 hPa and temperature from -40 ℃ to 80 ℃. DFRobot SEN0251
Module with digital barometer BMP581. It enables pressure measurement in the range from 300 to 1250 hPa with an accuracy of ± 5 Pa and communicates via I2C. SparkFun SEN-20171
The GY-BMP280 is an atmospheric pressure sensor module. It allows measurement in the range of 300 ... 1100 hPa with an accuracy of 1 hPa. The sensor uses I2C or SPI bus
Precision sensor from Bosch for measuring humidity with ±3% accuracy, barometric pressure with ±1 hPa absolute accuraccy, and temperature with ±1.0°C accuracy Adafruit 2652