- Out-of-Stock
![ArduCAM-LF Rev. C+ Dotykowy LCD TFT 3,2'' Shield dla Arduino z kamerą OV2640 2Mpx ArduCAM-LF Rev. C+ Dotykowy LCD TFT 3,2'' Shield dla Arduino z kamerą OV2640 2Mpx](https://kamami.pl/27724-large_default/arducam-lf-rev-c-lcd-touch-tft-32-shield-for-arduino-with-ov2640-2mpx-camera.jpg)
Arducam-LF Rev.C+ Camera module + 3.2 inch LCD for arduino UNO MEGA2560 DUE. ArduCam B0052+B0011
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
ArduCAM series camera shield is a universal camera control board for Arduino. It hides the complex nature of the camera and provides the easy to use camera control interface as well as the ready to use software source code library and demo code. The ArduCAM supports variety camera modules from 0.3MP to 5MP with different format like RAW, RGB, YUV, JPEG and can be well mated with standard Arduino boards.
ArduCAM Rev.C+ is the latest revision of ArduCAM shields, it offers the improved performance and enhanced functions than the previous revisions. It can capture maxim 5MP JPEG images, which makes it to be the ideal solution for IoT applications.
The ArduCAM is designed for Arduino but not limited to Arduino, it can be used in any platforms like Arduino, Raspberry Pi, Maple, Chipkit, Beaglebone black, as long as they have the SPI and I2C interface. User can port the current Arduino library to other platforms with less effort.
Table 1 Supported Camera Modules
Resolution | Sensor Vendor | Camera Module | Manufacture |
0.3MP | Omnivision | OV7660 / OV7670 / OV7675 / OV7725 | ArduCAM |
0.3MP | Aptina | MT9V111 | ArduCAM |
1.3MP | Aptina | MT9M112 / MT9M001 | ArduCAM |
2MP | Omnivision | OV2640 | ArduCAM |
2MP | Aptina | MT9D111 / MT9D112 | ArduCAM |
3MP | Omnivision | OV3640 | ArduCAM |
3MP | Aptina | MT9T112 | ArduCAM |
5MP | Omnivision | OV5640 / OV5642 | ArduCAM |
Functions
Single capture mode is the default capture mode of the camera. After issuing a capture command via SPI port, the ArduCAM will wait for a new frame and buffer the one entire image data to the frame buffer, and then assert the completion flag bit in the register. User only needs to poll the flag bit from the register to check out if the capture is done.
Multiple capture mode is advanced capture mode. By setting the number of frames in the capture register, the ArduCAM will capture consequent frames after issuing capture command. Note that number of frames should be set properly and make sure do not exceed the maximum memory space.
The JPEG compression function is implemented in the image sensor. With proper register settings to the sensor, user can get different resolution with JPEG image stream output. It is recommended to use JPEG output to get higher resolution than RGB mode, due to the limitation of frame buffer.
Normal read operation reads each image data by sending a read command in one SPI read operation cycle. While burst read operation only need to send a read command then read multiple image data in one SPI read operation cycle. It is recommended to use burst read operation to get better throughput performance.
Sometimes user wants to read the same frame of image data multiple times for processing, the rewind read operation is designed for this purpose. By resetting the read pointer to the beginning of the image data, user can read the same image data from the start point again.
Some battery power device need save power when in the idle status, the ArduCAM offers the low power mode to reduce power consumption, by shutdown the sensor and memory circuits.
Image sensor control function is implemented in the image sensor. By setting proper set of register settings, user can control the exposure, white balance, brightness, contrast, color saturation and etc.
A set with ATmega2560 microcontroller (256 kB Flash, 8 kB RAM, 4 kB EEPROM) clocked at 16 MHz. The user has, among others: 54 I / O lines, 14 PWM channels, 16 analog inputs. Arduino A000067
Arducam-F Rev.C+ Camera module shield with OV2640 for Arduino UNO MEGA2560 DUE. ArduCam B0051+B0011
No product available!
No product available!
Wide Input Voltage 3.0 A Step Down Regulator, SOIC8, RoHS, Allegro MicroSystems
No product available!
No product available!
No product available!
Printed circuit board for the Lattice PLP programmer
No product available!
Computer fan housing Raspberry Pi 3, Raspberry Pi 2 model B and Raspberry Pi 1 model B + in dark red plastic color
No product available!
A circuit board for a universal 2-channel relay module. AVT1914 A
No product available!
No product available!
No product available!
Universal organizer with compartments. Allows you to store small parts and tools. BOX0002
No product available!
High voltage differential probe. It has good measurement parameters: 100 MHz band and operating voltage up to 1300 V. The probe has two damping factors: 50X and 500X. Micsig DP10013
No product available!
Printed circuit board with Lock code lock programmed. AVT5601 A +
No product available!
Turnigy Multistar 20 A - Brushless motor controller for 2-4S multirotors (OPTO) (HK27775)
No product available!
ROSA3D filament made of high-quality PLA granules. 3 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D PLA Starter Gray
No product available!
No product available!
Bernard Ziętek
No product available!
Arducam-LF Rev.C+ Camera module + 3.2 inch LCD for arduino UNO MEGA2560 DUE. ArduCam B0052+B0011