- Out-of-Stock
Tensometric beam with a maximum load of 2 kg 80mm
ID: 585167
Aluminum tensometer beam, allowing weight measurement up to 2 kilograms. It has four wires. It is used in kitchen scales and portable scales
Description
Aluminum strainer beam, mounted on screws (not included), screwed in with threaded holes. The beam allows you to measure weight up to 2 kilograms. It has four wires.
Features
- Weight measurement up to 2 kg
- Supply voltage: recommended 5 - 12 V DC, maximum: 15 V DC
- Input resistance: 1115 Ω
- Output resistance: variable (no load: 1000 Ω)
- dimensions: 13 x 13 x 80 mm
- Spacing: 15mm
- Cable length: 25 cm
The importance of wire colors:
- red ("+" DC boost power)
- black ("-" DC boost power)
- white ("+" output signal)
- green ("-" output signal)
585167
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
The module allows you to attach a strain gauge (working in the Wheatstone bridge circuit) and convert the analog signal into its digital representation, available on the module output lines. The system processes the signal with a 24-bit resolution and can be powered by 2.7V - 5.5V. The module is especially recommended for constructing digital scales in combination with Arduino
zł4.69
24h
Available quantity: 2
Available
The SparkFun Load Sensor Combinator is a bare PCB that combines four load sensors into a standard four-wire Wheatstone bridge configuration. BOB-13878
zł13.26
24h
Available quantity: 5
Available
Simple-to-use, open source solution for measuring weight and temperature with the ability to read multiple types of load cells and offers a simple-to-use serial menu to configure calibration value, sample rate, time stamp and units of precision. SEN-13261
zł178.41
24h
Available quantity: 2
Available
Other products in the same category (16)
Test probe tip with 500X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 100 MHz and 200 MHz frequency bands. Micsig OP500-2
Product available on request. Please send your inquiry to the following address: sales@kamami.com
Retired
No product available!
ZD-409 resistance soldering machine with a power of 48W is a tool useful when disassembling SMD and DIL components on printed circuits.
Retired
No product available!
The Micsig DP series differential probe is based on advanced metal shielding technology. It offers a 150 MHz frequency band and the ability to measure voltages up to 7000 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig DP7001
Retired
No product available!
No product available!
USB - LIN bus converter module. It allows you to connect devices to your computer via the LIN bus. LIN USB CONVERTER (LUC)
Retired
No product available!
No product available!
A pre-installed radio for everyone. AVT5540 C
Retired
No product available!
No product available!
No product available!
No product available!
No product available!
No product available!
Assembled siren for emergency vehicles. AVT789 C
Retired
No product available!
No product available!
CONVERTER AND CHARGER FOR LITHIUM BATTERIES - A KIT FOR INDEPENDENT INSTALLATION
Delivery date unknown
No product available!
Module with the PIR EKMB1107112 motion sensor, the standby power consumption of up to 1 uA. SparkFun SEN-17373
zł158.49
24h
Available quantity: 1
Available
Aluminum tensometer beam, allowing weight measurement up to 2 kilograms. It has four wires. It is used in kitchen scales and portable scales