.png)
Voltage Regulator module 7.5V Step-Down 5A D36V50F7
ID: 586584
5906623480371
zł170.15
Tax included
zł138.33 tax excl.
Step-Down converter D36V50F7 with an output voltage of 7.5 V, an input voltage from 8.3 to 50 V and a maximum output current of 7 A. Pololu 4093
Description
Step-Down converter module D36V50F7 with an output voltage of 7.5 V and an input voltage from 8.3 to 50 V. The maximum current load of the module is from 3 to 7 A and depends on the input voltage. The inverter achieves standard efficiency above 80-95%, which is dependent on the input voltage and load. The module is protected against reverse polarity, overheating, overload and short circuit.
Pinot
- VIN - power input
- GND - ground
- VOUT - output
- PG - an open drain output that goes low when the regulator's output voltage rises more than 20% above or drops by more than 10% below the nominal voltage
- EN - converter is enabled by default (100 kΩ pull-up resistor on the board connects EN pin with VIN). The ENABLE pin can be set low to turn off the power and put the board into a low-power state.
- VRP - provides access to the input voltage before protection against voltage reverse polarity. Can be used as an output to power other devices or the input voltage can be connected to VRP instead of VIN to bypass protection.
Features
- Input voltage: 8.3 to 50V
- Output voltage: 7.5V
- Type. maximum current: from 3 to 7 A
- Built-in protection against overheating, overload, short circuit and reverse polarity
- Type. efficiency: 80-95%
- Switching frequency: approx. 500 kHz under heavy loads
- Energy saving mode
- Typical quiescent current from 2 mA to 4 mA
- EN input with a precise cut-off threshold to disconnect the load and put the controller into a low-power state
- Power good output, which indicates when the controller cannot maintain the output voltage adequately
- The soft-start function limits the inrush current and gradually increases the output voltage
- Three mounting holes M2
- Dimensions: 25.4 x 25.4 x 9.5 mm
Parameters
Kit contains
- D36V50F7 converter module
- 12-pin straight goldpin connector
586584
Data sheet
- Output voltage
- 7,5 V
- Output current
- 5A
- Converter type
- Step-down
- Supply voltage min
- 8,3 V
- Supply voltages max
- 50 V
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
You might also like
The trigger module is designed for chargers PD 2.0 and PD 3.0. It is equipped with a USB type C input and an output on a 5.08 mm ARK screw connector. Allows you to power devices with 5 V, 9 V, 12 V, 15 V and 20 V and test chargers by replacing the PD device
zł27.05
24h
Available quantity: 18
Available
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
zł5.33
24h
Available quantity: 186
Available
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
zł4.48
24h
Available quantity: 373
Available
A set of 40 pcs of male-male connecting cables in various colors, 10 cm long
zł5.63
24h
Available quantity: 903
Available
Step-Down converter D36V50F3 with an output voltage of 3.3 V, an input voltage from 4.5 to 50 V and a maximum output current of 9.5 A. Pololu 4090
zł150.68
24h
Available quantity: 1
Available
Step-Down converter D36V50F5 with an output voltage of 5 V, an input voltage from 5.5 to 50 V and a maximum output current of 8 A. Pololu 4091
zł172.03
24h
Available quantity: 2
Available
Other products in the same category (16)
No product available!
Available
No product available!
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 3.3 V. The board measures only 0.7″ × 0.7″, but it allows a typical continuous output current of up to 2.5 A. Typical efficiencies of 80% to 95% make this regulator well suited for powering moderate loads like sensors or small motors.
zł121.88
4 weeks
No product available!
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 6 V. The board measures only 0.7″ × 0.7″, but it allows a typical continuous output current of up to 2.5 A. Typical efficiencies of 85% to 95% make this regulator well suited for powering moderate loads like sensors or small motors.
zł101.22
4 weeks
No product available!
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 7.5 V. The board measures only 0.7″ × 0.7″, but it allows a typical continuous output current of up to 2.5 A. Typical efficiencies of 85% to 95% make this regulator well suited for powering moderate loads like sensors or small motors.
zł104.30
24h
Available quantity: 2
Available
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 9 V. The board measures only 0.7″ × 0.7″, but it allows a typical continuous output current of up to 2.5 A. Typical efficiencies of 85% to 95% make this regulator well suited for powering moderate loads like sensors or small motors.
zł98.65
4 weeks
No product available!
This synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 5 V with an available output current of around 9 A.
zł149.86
24h
Available quantity: 3
Available
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 5 V. The board measures only 0.7″ × 0.8″, but it allows a typical continuous output current of up to 5 A. Typical efficiencies of 85% to 95% make this regulator well suited for high-power applications like powering motors or servos.
zł148.19
24h
Available quantity: 3
Available
Step-Down Voltage Regulator D24V25F5. Pololu 2850
zł98.86
24h
Available quantity: 3
Available
The compact (0.4″ × 0.5″) D24V5F15 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 15 V while allowing for a maximum output current of 500 mA. Pololu 2847
zł38.57
24h
Available quantity: 1
Available
The compact (0.4″ × 0.5″) D24V5F12 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 12 V while allowing for a maximum output current of 500 mA.
zł33.19
24h
Available quantity: 6
Available
The compact (0.4″ × 0.5″) D24V5F9 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 9 V while allowing for a maximum output current of 500 mA. Pololu 2845
zł38.40
4 weeks
No product available!
The compact (0.4″ × 0.5″) D24V5F6 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 6 V while allowing for a maximum output current of 500 mA. Pololu 2844
zł33.73
24h
Available quantity: 3
Available
The compact (0.4″ × 0.5″) D24V5F5 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 5 V while allowing for a maximum output current of 500 mA. Pololu 2843
zł32.90
24h
Available quantity: 11
Available
The compact (0.4″ × 0.5″) D24V5F2 synchronous buck voltage regulator takes input voltages between 3 V and 36 V and efficiently reduces them to 2.5 V while allowing for a maximum output current of 500 mA. This regulator offers typical efficiencies between 80% and 90%. The pins have a 0.1″ spacing, making this board compatible with standard solderless breadboards and perfboards.
zł37.85
4 weeks
No product available!
Step-Down converter D36V50F7 with an output voltage of 7.5 V, an input voltage from 8.3 to 50 V and a maximum output current of 7 A. Pololu 4093