New products
New products New products
zł119.00
Delivery date unknown
zł119.00
Delivery date unknown
Voltage Regulator module 3.3V Step-Down 3.6A D36V28F3
ID: 586587
5906623413126
zł83.26
Tax included
zł67.69 tax excl.
Step-Down converter D36V28F3 with an output voltage of 3.3 V, an input voltage from 4.5 to 50 V and a maximum output current of 4.5 A. Pololu 3781
Description
Step-Down converter module D36V28F3 with an output voltage of 3.3 V and an input voltage from 4.5 to 50 V. The maximum current load of the module is from 3.2 to 4.5 A and depends on the input voltage. The inverter achieves a standard efficiency of over 80-90%, which is dependent on the input voltage and load. The module is protected against reverse polarity, overheating, overload and short circuit.
Pinout
- VIN - power input
- GND - ground
- VOUT - output
- PG - an open drain output that goes low when the regulator's output voltage rises more than 20% above or drops by more than 10% below the nominal voltage
- EN - converter is enabled by default (100 kΩ pull-up resistor on the board connects EN pin with VIN). The ENABLE pin can be set low to turn off the power and put the board into a low-power state.
Features
- Input voltage: 4.5 to 50V
- Output voltage: 3.3V
- Type. maximum current: from 3.2 to 4.5 A
- Built-in protection against overheating, overload, short circuit and reverse polarity
- Type. efficiency: 80-90%
- Switching frequency: approx. 500 kHz under heavy loads
- Energy saving mode
- Typical quiescent current from 2 mA to 3 mA
- EN input with a precise cut-off threshold to disconnect the load and put the controller into a low-power state
- Power good output, which indicates when the controller cannot maintain the output voltage adequately
- The soft-start function limits the inrush current and gradually increases the output voltage
- Two M2 mounting holes
- Dimensions: 17.8 x 20.3 x 8.8 mm
Parameters
Kit contains
- D36V28F3 converter module
- Straight 6-pin goldpin connector
- 5-pin angled goldpin connector
586587
Data sheet
- Output voltage
- 3,3 V
- Output current
- 3,6 A
- Converter type
- Step-down
- Supply voltage min
- 4,5 V
- Supply voltages max
- 50 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
The Step-Up Buck Voltage Regulator module with adjustable output voltage in range of 4-25V with a input voltage range of 1.5-16V and a maximum output current of 2A. Pololu 799
zł88.63
24h
Available quantity: 2
Available
The trigger module is designed for chargers PD 2.0 and PD 3.0. It is equipped with a USB type C input and an output on a 5.08 mm ARK screw connector. Allows you to power devices with 5 V, 9 V, 12 V, 15 V and 20 V and test chargers by replacing the PD device
zł29.50
24h
Available quantity: 2
Available
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
zł4.35
24h
Available quantity: 154
Available
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
zł4.31
Delivery date unknown
No product available!
A set of 40 pcs of male-male connecting cables in various colors, 10 cm long
zł5.49
Delivery date unknown
No product available!
Step-Down converter D36V50F3 with an output voltage of 3.3 V, an input voltage from 4.5 to 50 V and a maximum output current of 9.5 A. Pololu 4090
zł137.49
24h
Available quantity: 1
Available
Other products in the same category (16)
Waterproof DC-DC Step-Down Converter with 8 to 22V input voltage and 5V 3A USB output
zł19.85
4 weeks
No product available!
DC-DC Step-Down converter module AP63203 with an output voltage of 3.3 V, an input voltage of 3.8 to 32 V and a maximum output current of 2 A. SparkFun COM-18356
zł35.65
24h
Available quantity: 2
Available
DC-DC Buck Converter 5–36 V with 5 V or 3.3 V output in the DC5-36-TO-DC3V3-5-M version is equipped with terminal and pin headers for quick deployment in power applications. High efficiency, adjustable voltage, and compact size make it suitable for powering microcontrollers, communication modules, and embedded systems.
zł15.35
24h
Available quantity: 4
Available
DC-DC Step Down converter module with input voltage from 7 to 24 V and output voltage of 5 V. Can supply currents up to 4 A. DFRobot DFR0831
zł21.97
24h
Available quantity: 10
Available
This compact (0.4″ × 0.5″) switching step-down (or buck) voltage regulator takes input voltages up to 50 V and efficiently reduces them to 9 V while allowing for a maximum output current of 600 mA. It has a very low dropout, so it can be used with input voltages that are within a few hundred millivolts of its output.
zł22.29
24h
Available quantity: 2
Available
Step-down converter with adjustable output voltage 1.2V-35V and current efficiency 9A. The module allows to limit the current consumption at the output via a multi-turn potentiometer. modxl4016sd
zł16.97
4 weeks
No product available!
The compact (0.4″ × 0.5″) D24V5F15 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 15 V while allowing for a maximum output current of 500 mA. Pololu 2847
zł35.76
24h
Available quantity: 1
Available
A power supply based on a DC-DC converter with a current capacity of up to 6.1 A. The input voltage can range from 6 V to 30 V, while the output voltage is adjustable from 0 V to 36 V. Enclosure version. XYL3606S
zł193.42
24h
Available quantity: 4
Available
The Step-Down D24V6F9 Buck Voltage Regulator module gives the output voltage of 9V with a wide input voltage range of 11.5-42V and a maximum output current of 600 mA. Pololu 2108
zł32.61
4 weeks
No product available!
Step-Down converter with an output voltage of 5 V, input voltage from 9 to 36 V and a maximum current of 5 A. The board is equipped with a DC input connector and an output USB connector
zł14.45
4 weeks
No product available!
The compact (0.4″ × 0.5″) D24V5F2 synchronous buck voltage regulator takes input voltages between 3 V and 36 V and efficiently reduces them to 2.5 V while allowing for a maximum output current of 500 mA. This regulator offers typical efficiencies between 80% and 90%. The pins have a 0.1″ spacing, making this board compatible with standard solderless breadboards and perfboards.
zł35.08
4 weeks
No product available!
Step-Down converter with adjustable output voltage from 1.25 to 36 V, input voltage from 4 to 38 V and maximum current up to 5 A
zł6.91
4 weeks
No product available!
Step-Down converter D36V50F9 with an output voltage of 9 V, an input voltage from 9.9 to 50 V and a maximum output current of 7 A. Pololu 4094
zł156.87
4 weeks
No product available!
Przetwornica DC-DC Step Down (MP1584), Uwe 4.5..28V, Uwy regulowane 0.8..20V, RoHS
zł4.77
24h
Available quantity: 56
Available
The Step-Down D24V3F3 Buck Voltage Regulator module gives the output voltage of 3,3V with a wide input voltage range of 4.3-42V and a maximum output current of 300 mA. Pololu 2097
zł33.54
24h
Available quantity: 2
Available
Step Down converter module with an output voltage of 5 V and a maximum current of 2x2,5 A. The board is equipped with four USB connectors
zł23.59
24h
Available quantity: 5
Available
Step-Down converter D36V28F3 with an output voltage of 3.3 V, an input voltage from 4.5 to 50 V and a maximum output current of 4.5 A. Pololu 3781