

A DC / DC converter that reduces the input voltage to 6 V. The maximum current efficiency of the inverter module is 2.5 A, which is the maximum continuous current that can be taken from the inverter. The efficiency of the converter ranges from 85 to 95%, which makes it a much better solution than linear voltage stabilizers. The inverter has reverse voltage protection, protection against short-circuiting output, soft start system and temperature protection. The inverter manufacturer has derived two additional signals, "enable" by means of which the inverter can be switched on or off and a "power-good" output, the state of which changes when the inverter is unable to maintain a stable voltage. The typical current consumption of the inverter is about 1 mA, while in the low-power mode the inverter takes about 5-10 uA for each Volt of the input voltage.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
The Step-Down D24V3F12 Buck Voltage Regulator module gives the output voltage of 12V with a wide input voltage range of 14.5-42V and a maximum output current of 300 mA. Pololu 2100
No product available!
The compact (0.4″ × 0.5″) D24V5F6 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 6 V while allowing for a maximum output current of 500 mA. Pololu 2844
The compact (0.4″ × 0.5″) D24V5F1 synchronous buck voltage regulator takes input voltages between 3 V and 36 V and efficiently reduces them to 1.8 V while allowing for a maximum output current of 500 mA. This regulator offers typical efficiencies between 75% and 90%. The pins have a 0.1″ spacing, making this board compatible with standard solderless breadboards and perfboards.
No product available!
DC-DC Step-Down converter module AP63203 with an output voltage of 3.3 V, an input voltage of 3.8 to 32 V and a maximum output current of 2 A. SparkFun COM-18356
The Step-Down D24V6F12 Buck Voltage Regulator module gives the output voltage of 12V with a wide input voltage range of 15-42V and a maximum output current of 600 mA. Pololu 2109
No product available!
This compact (0.4″ × 0.5″) switching step-down (or buck) voltage regulator takes input voltages up to 50 V and efficiently reduces them to 15 V while allowing for a maximum output current of 600 mA. It has a very low dropout, so it can be used with input voltages that are within a few hundred millivolts of its output.
Step-Down DC-DC converter module based on the D24V150F12 chip. Input voltage 14.5 ... 40V, output voltage 12V (max 15A). Pololu 2885
The compact (0.4″ × 0.5″) D24V5F9 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 9 V while allowing for a maximum output current of 500 mA. Pololu 2845
No product available!
Step-Down converter D36V28F7 with an output voltage of 7.5 V, an input voltage from 8 to 50 V and a maximum output current of 3.7 A. Pololu 3784
An efficient step-down converter that steps down the input voltage from as low as 45 V to a regulated output voltage range of 1.4 to 7 V, offering high efficiency and a maximum continuous current of 3.4 A. It has built-in reverse polarity, overload and short circuit protection, and the spread spectrum function reduces EMI interference. Pololu 4873
Step-Down converter D36V50F3 with an output voltage of 3.3 V, an input voltage from 4.5 to 50 V and a maximum output current of 9.5 A. Pololu 4090
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 7.5 V. The board measures only 0.7″ × 0.7″, but it allows a typical continuous output current of up to 2.5 A. Typical efficiencies of 85% to 95% make this regulator well suited for powering moderate loads like sensors or small motors.
Step-Down converter D36V28F5 with an output voltage of 5 V, an input voltage from 5.3 to 50 V and a maximum output current of 4 A. Pololu 3782
Step-Down DC-DC converter module based on the D24V150F7 chip. Input voltage 9..40V, output voltage 7.5V (max 15A). Pololu 2883
No product available!
Step-Down converter D36V50F5 with an output voltage of 5 V, an input voltage from 5.5 to 50 V and a maximum output current of 8 A. Pololu 4091
No product available!
A power supply based on a DC-DC converter with a current capacity of up to 5 A. The input voltage can range from 6 V to 36 V, while the output voltage is adjustable from 0.6 V to 36 V. XYS3580
Step-Down DC-DC converter module based on the D24V150F9 chip. Input voltage 11 ... 40V, output voltage 9V (max 15A). Pololu 2884
The very small step-down 6 V, 2.5 A synchronous inverter can be supplied with voltage up to 36 V, dimensions: 17.8 mm x 17.8 mm. Pololu 2859