Core405R
search
  • Core405R
ID: 1180627
zł98.26
Tax included

zł79.89 tax excl.

Development kit with STM32F405RGT6 microcontroller. Requires an external programmer with SWD or JTAG interface. Waveshare Core405R

4 weeks
On request
Kamami is the official distributor of Waveshare displays, accessories and modules.

Description

Development kit with a microcontroller from the STM32F405RG family (ARM Cortex-M4 core). It was equipped with the basic elements needed to start the system, configuration switches and a reset button. The user has at his disposal all pins of the system led out to pin connectors with a pitch of 2.54 mm. It is powered via the miniUSB connector and programmed via the JTAG or SWD interface. There is no debugger on the board, therefore the set requires an external programmer / debugger. Full documentation is available on the product page.

  1. STM32F405RGT6:the high performance STM32 MCU which features:
    • Core: Cortex-M4 32-bit RISC
    • Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz
    • Operating Voltage: 1.8V-3.6V
    • Package: LQFP64
    • Memories: 1MB Flash, 192+4kB SRAM
    • MCU communication Interfaces:
      • 3 x SPI, 4 x USART, 2 x UART, 2 x I2S, 3 x I2C, 1 x SDIO, 2 x CAN
      • 1 x USB 2.0 HS/FS device/host/OTG controller with dedicated DMA, on-chip full-speed PHY
      • 1 x USB HS ULPI (external PHY required)
    • AD & DA converters: 3 x AD (12-bit, 1μs, shares 16 channels); 2 x DA (12-bit)
    • Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP
  2. AMS1117-3.3: 3.3V voltage regulator
  3. MIC2075-2: onboard USB power management device
  4. Power supply switch, powered from 5Vin or USB connection
  5. Boot mode selection, for configuring BOOT0 pin
  6. Power indicator
  7. VBUS LED
  8. Reset button
  9. 8M crystal
  10. 32.768K crystal, for internal RTC with calibration
  11. JTAG/SWD interface: for debugging/programming
  12. USB connector, used for establishing USB communication between PC and the STM32 development board
  13. MCU pins expander, VCC, GND and all the I/O pins are accessible on expansion connectors for further expansion
  14. 5Vin pinheader, 5V power supply is required when using USB HOST/OTG
  15. USB jumper
    • short the jumper when using USB
    • open the jumper to disconnect from related I/O port
  16. VBAT selection jumper
    • short the jumper to use system power supply
    • open the jumper to connect the VBAT to external power, such as battery

Features

  • STM32F405RG microcontroller
  • Configuration switches and jumpers
  • MiniUSB power connector
  • Power LED
  • SWD and JTAG interface
  • Reset button
  • 3.3 V regulator

Kit contains

  • Core405R
  • MiniUSB cable
1180627

Manufacturer

  • BTC Korporacja sp. z o. o.
  • Ludwinowo Zegrzyńskie 52G
  • 05-140 Ludwinowo Zegrzyńskie
  • Poland
  • [email protected]
  • 22 767 36 20

Responsible person

  • BTC Korporacja sp. z o. o.
  • Ludwinowo Zegrzyńskie 52G
  • 05-140 Ludwinowo Zegrzyńskie
  • Poland
  • [email protected]
  • 22 767 36 20

You might also like

Other products in the same category (16)