Gravity: AHT20 Temperature and Humidity - module with a temperature and humidity sensor
ID: 1181310
5902186310612
zł22.30
Tax included
zł18.13 tax excl.
A module with a temperature and humidity sensor based on the AHT20 system. Equipped with a Gravity connector, it communicates via the I2C interface. DFRobot SEN0528
Description
A module with a temperature and humidity sensor based on the AHT20 system. It has an accuracy of ± 2% when measuring relative humidity from 20 to 80% and an accuracy of ± 0.3 ° C when measuring temperatures from 20 to 60 ° C. The module is compatible with 2V and 5V controllers, and communication is via the I2C interface (Gravity connector). Full documentation is available on the product page.
Features
- Temperature measurement range: -40 to 85 ° C (accuracy: ± 1 ° C in the entire range)
- Humidity measuring range: 0 to 100% RH (accuracy: ± 3% RH over the entire range)
- I2C interface (address 0x38)
- Supply voltage: 2 V to 5 V
- Dimensions: 30 x 20.5 mm
Kit contains
- Gravity: AHT20 Temperature and Humidity Sensor
- Gravity 4-pin I2C / UART cable
1181310
Data sheet
- Interface
- I2C
- Type of sensor
- AHT20
- Power supply voltage
- 2.0..5.5V
- Sensor type
- Temperatury
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.57
24h
Available quantity: 92
Available
Available
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
zł21.92
24h
Available quantity: 4
Available
Other products in the same category (16)
Available
Waterproof temperature sensor adapted to work with Sonoff TH10 / TH16
zł43.27
4 weeks
No product available!
A module with a temperature sensor based on the absorption of infrared radiation. Enables non-contact measurement. modTMP006
zł51.82
4 weeks
No product available!
LM35 analog temperature sensor module for Arduino. DFRobot DFR0023
zł15.88
4 weeks
No product available!
Gravity: DS18B20 Temperature Sensor is a module with a temperature sensor compatible with Arduino boards. The module can be supplied with 3.3-5V voltage and measures the temperature in the range -55 ~ 125 ° C. DFRobot DFR0024
zł24.44
24h
Available quantity: 4
Available
Module with MLX90614-DCI sensor for non-contact temperature measurement in the range from -70℃ to 270℃. I2C communication. DFRobot SEN0263
zł359.76
4 weeks
No product available!
Module with NXP temperature sensor. It allows you to measure temperature in the range from -55 °C to +125 °C. I2C interface. The board is equipped with a Pmod I2C standard connector and a KAMAMI connector
zł17.90
24h
Available quantity: 382
Available
High temperature measuring kit. It consists of a signal conversion module with a range of -270°C to 1372°C and a K-type thermocouple probe with a range of up to 800°C. I2C communication DFRobot DFR0558
zł126.64
4 weeks
No product available!
Module with DS18B20 temperature sensor from Dallas Semiconductor. The sensor used allows you to measure temperatures in the range -55 ~ 125 ° C with an accuracy of ± 0.5 ° C (in the range of -10 ~ 85 ° C). The 1-Wire interface is used for communication. The plate is equipped with a goldpin connector and a KAMAMI connector, allowing easy connection of the module to the commissioning kits.
zł13.90
24h
Available quantity: 348
Available
Non-contact temperature sensor. Used to measure the infrared intensity of an object to calculate the surface temperature without a contact point in the range -70 ... 380 ° C. DFRobot SEN0256
zł415.47
24h
Available quantity: 1
Available
Non-contact temperature sensor with a measuring range from -70 to 380°C. It uses infrared waves and has a current output. DFRobot SEN0264
zł398.88
4 weeks
No product available!
Temperature sensor based on the DS18B20 system in a water proof measuring probe. Communication via the 1-Wire interface. DFRobot DFR0198
zł26.56
24h
Available quantity: 5
Available
A set with a temperature sensor based on the DS18B20 system in the form of a waterproof measuring probe, a sensor adapter and a cable. Communication via the 1-Wire interface. DFRobot KIT0021
zł26.14
24h
Available quantity: 2
Available
Module with the MCP9600 amplifier designed to work with a K-type thermocouple. The module has a PCC connector for connecting this type of thermocouple. I2C communication. SparkFun SEN-16294
zł146.78
24h
Available quantity: 1
Available
Module with the MCP9600 amplifier designed to work with a K-type thermocouple. The module has a screw connector for connecting this type of thermocouple. I2C communication. SparkFun SEN-16295
zł147.93
24h
Available quantity: 1
Available
Module with digital temperature sensor TMP102. It enables temperature measurement in the range from –40°C to 125°C with an accuracy of 0.5°C. The system communicates via the I2C interface. SparkFun SEN-16304
zł32.75
24h
Available quantity: 1
Available
A module with a temperature and humidity sensor based on the AHT20 system. Equipped with a Gravity connector, it communicates via the I2C interface. DFRobot SEN0528