Category: STARTER KITS, PROGRAMMERS, MODULES

Module with an RFID tag based on the ST25DV16K chip. It can be reprogrammed via the I2C bus. Equipped with STEMMA QT connector and PCB antenna. Adafruit 4701

NUCLEO series starter kit featuring STM32C031C6 microcontroller (32 kB Flash, Cortex-M0+), with built-in ST-Link/v2 programmer-debugger, equipped with Arduino-compatible connectors. STMicroelectronics NUCLEO-C031C6

Starter kit for the micro:bit v2. The kit includes an expansion module with Grove connectors, Grove modules with sensors and the necessary accessories. Seeed Studio 110060762

A development board based on the Silicon Labs EFR32MG24 SoC that supports Matter®, Thread®, and Bluetooth® Low Energy 5.3, making it ideal for IoT applications such as smart homes and wearables. With 4MB Flash and 256kB RAM, the board enables more complex applications, including AI, and its low power consumption makes it an excellent choice for battery-powered projects. The board offers broad compatibility with additional XIAO modules, allowing for easy expansion of projects, and built-in security features ensure data and applications are protected. Seeed Studio 102010610

Board with WiFi Espressif ESP32-S2 module and 0.96" LCD display. It offers 4 MB Flash memory and 8 MB SRAM. Leads are compatible with HAT modules for Raspberry Pi Pico. Waveshare ESP32-S2-LCD-0.96-M

3-port Hub with Grove connectors for M5Stack sets. It allows you to connect several devices with Grove connectors to the evaluation kit. M5Stack HUB Unit

The board with the RP2040 microcontroller equipped with two ARM Cortex-M0+ cores, which work at a frequency of 133 MHz, 256 kB RAM. The board also has 8 MB of QSPI flash memory. The system can be programmed in C/C++ or MicroPython. Adafruit 4884

This sensor utilizes advanced signal processing technology by using a powerful chip (XKC-Y25-T12V) with high-speed operation capacity to achieve non-contact liquid level detection; suitable for hazardous applications: detecting toxic substances and all kinds of liquid in an airtight container under high pressure. SEN0204

ESP-PROG is an advanced tool for programming and debugging Espressif microcontrollers such as ESP32, ESP32-C3, ESP32-S2, ESP32-S3 and ESP8266. With the built-in FT2232HL USB bridge, ESP-PROG converts the USB 2.0 interface to serial and parallel interfaces, offering functions of automatic firmware download, serial communication and online debugging via JTAG

Module with 24-bit ADC NAU7802 converter. It enables reading data from strain gauges and scales. I2C interface. SparkFun SEN-15242

Gravity: I2C 3.7V Li Battery Fuel Gauge is a module for monitoring the parameters of the Li-ion battery allowing for precise measurement of the flow of charge to / from a 1-source source with an input voltage of 2.5-4.2V. DFRobot DFR0563

The MPLAB Snap In-Circuit Debugger/Programmer allows affordable, fast and easy debugging and programming of PIC, dsPIC, AVR and SAM flash MCUs. Microchip PG164100

Development board with WiFi and Bluetooth module Espressif ESP32-WROVER. It is equipped with a microSD card slot, a USB-UART converter and a Li-Ion battery charging system. TTGO T8 V1.1 ESP32

Module with an 8-channel ADC converter with 8-bit resolution. It uses the ADS7830 chip and is equipped with a STEMMA QT connector, thanks to which it communicates via the I2C interface. Adafruit 5836

Shield for STM32 series Nucleo, XNucleo and Arduino series for communication via RS485 and CAN interfaces (CAN is only available for Nucleo and XNucleo plates). Shield is based on MAX3485 and SN65HVD230 systems

The ESP32-C6 is a versatile microcontroller with support for WiFi 6 and Bluetooth 5, designed for a wide range of applications in smart homes, industry, and consumer electronics. With support for multiple interfaces and development environments, this board offers the flexibility and performance needed to execute advanced projects. Compatibility with Raspberry Pi Pico HAT extensions further enhances its capabilities, making it an ideal choice for developers and engineers. Waveshare 26845

M5Stack series development kit equipped with ESP32 Pico. It will work in IoT-related projects or in "wearable" devices. M5Stack C008

Module with 9-axis IMU sensor BNO055. It has a built-in processing chip that returns orientation in 3D space. Communicates via I2C. Adafruit 4646

DEV-13912

A set of 10 cables, 30 cm long, compliant with the Gravity standard. DFRobot FIT0513