Category: STARTER KITS, PROGRAMMERS, MODULES

A small module, matching the breadboard, containing a 32-bit microcontroller with ARM Cortex M7 core. PJRC TEENSY40

Wi-Fi module based on the ESP8266 system - simplicity of use (communication through UART, supports AT commands), 3.3V power supply, support for WPA / WPA2 encryption - these features make the EPS8266 module applicable anywhere, where reliable and effective data transmission. The module is not equipped with an antenna, it should be attached using the U.FL connector. ESP-05

Development board with NXP iMXRT1062 ARM Cortex-M7 microcontroller. Equipped with a microSD slot. Version without Ethernet communication. PJRC TEENSY41-NE

WiFI 802.11 b/g/n module. Equipment includes, among others: LED diode, antenna, 8 pins with 2.54mm pitch (including 3 GPIO lines). Power supply: 3.3V.

8-position DIP-Switch Module

Base Shield V2 is an extension for tiles with an Arduino shield connector, it has a Grove connector, which can be connected to Grove-compatible modules / sensors. Seeedstudio 103030000

Pressure sensor module with I2C interface (MPL115A2)

STM32 Nucleo-64 development board with STM32F446RET6 MCU, supports Arduino and ST morpho connectivity

Development board D1 Mini with WiFi module ESP-8266MOD and 4 MB Flash memory. The module can be programmed from the Arduino IDE level. WeMos D1 Mini

Compact tool for debugging and programming STM32 microcontrollers via JTAG / SWD interfaces. STMicroelectronics STLINK-V3MINIE

STM32 Nucleo-64 development board with STM32L476RGT6 MCU, supports Arduino and ST morpho connectivity

Flexible Qwiic cable, 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single female goldpin connectors. SparkFun PRT-17261

Discovery kit based on STM32G431CB microcontroller, L6387 controller and STL180N6F7 MOSFET power transistors. Designed to drive a 3-phase brushless motor (BLDC/PMSM) and implement both sensorless FOC or 6-step algorithm. STMicroelectronics B-G431B-ESC1

Board with RP2040 microcontroller and W5100S network chip. The module is equipped with an Ethernet connector. WIZnet W5100S-EVB-Pico

SIMATIC LOGO! SOFT Comfort V8 from Siemens with a license for one device. It is designed to support LOGO! 8 controllers. The kit includes a DVD with software and documentation. Siemens 6ED1058-0BA08-0YA1

NUCLEO series starter kit equipped with STM32G431KB microcontroller (128 kB Flash, Cortex-M4), with built-in programmer-debugger ST-Link-V3E, equipped with connectors compatible with Arduino Nano.

KAmod ESP32 ETH+POE is a board equipped with the ESP32-WROOM module, enabling communication via Wi-Fi 2.4 GHz and Ethernet with a typical RJ45 connector, integrated with a USB-UART converter and a PoE power supply system compliant with IEEE 802.3af/at. The design of the board with dimensions of 85x56 mm resembles the Raspberry Pi family, and on the 40-pin connector there are all important I/O ports and supply voltages of 5 V and 3.3 V for powering additional components

Advanced module with a 32-bit, single-core RISC-V processor. It has a built-in Bluetooth LE 5 and IEEE 802.15.4 (Thread, Zigbee 3.0) module. Perfect solution for IoT (Internet of Things) projects. Version with soldered connectors. Waveshare ESP32-H2-DEV-KIT-N4-M