Category: STARTER KITS, PROGRAMMERS, MODULES

Module with an analog joystick that returns the X and Y position and the pressed state. The module has an ATtiny85 microcontroller on the board, which processes analog data of the joystick and sends it via the I2C interface. SparkFun COM-15168

A set with a radio transmitter and receiver operating at 433 MHz. The modules are equipped with Grove connectors and communicate via a digital interface. Seeed Studio 104020002

Module with integrated proximity and ambient light sensors and IR emitter in the VCNL4040 system. It allows the detection of obstacles in the range of 0 to 20 cm (no dead zone). It communicates via the I2C bus. SparkFun SEN-15177

Module with blue LED diode and potentiometer. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 104030010

Adapter dedicated to the Nintendo Wii Nunchuck. It allows you to connect the controller to the development board via the I2C interface. Adafruit 4836

Module with 8-bit ADC and 8-bit DAC. It allows you to measure voltage and generate an analog signal. Communicates via I2C. Adafruit 4648

Module with receiver designed for communication by means of a laser beam transmitted in the air. M5Stack Laser.Rx Unit

ESP32-S3-Touch-AMOLED-1.75-B is a development board based on the ESP32-S3 with a round AMOLED display and built-in protective enclosure, designed for projects requiring durability and compact integration. With Wi-Fi, Bluetooth, audio, sensors, and touch support, it is suitable for creating modern IoT and HMI devices.

The expansion module is designed to work with the Raspberry Pi 400. The board has a 40-pin connector placed in a vertical position and a connector for RPI 400 at an angle of 45°. Adafruit 4863

TPL5110 external counter module to turn on a project after a set time and save energy. The TPL5110\'s delay is configurable with resistors ranging from 100 ms to two hours. SparkFun PRT-15353

A mini module with a Qwiic connector designed for Raspberry Pi minicomputers. Qwiic SHIM uses a unique connector that snaps into the GPIO connector for a secure, solder-free connection. SparkFun DEV-15794

This encoders are designed for DFRobot 3PA and AWD Rovers. It can give you the rotation degree of the wheels. Encoder uses non-contact method to convert the angular displacement signals. Best fit with Micro DC Geared Motor. SEN0038

STM32L152D-EVAL is an advanced evaluation kit with the STM32L152ZDT6 microcontroller, integrating a wide range of peripherals and displays. It enables full testing of the chip’s capabilities and the development of low-power applications with access to multiple communication interfaces and diagnostic tools.

Adapter with galvanic isolation for STLINK-V3SET. It also allows the programmer to work with systems powered with voltages below 3.3 V. STMicroelectronics B-STLINK-ISOL

Module with L3G4200D (3-axis gyroscope with digital output)

Board for applications in the area of the Internet of Things (IoT). The module is based on the ESP-WROOM-32E system with 240 MHz clock, equipped with 4 MB Flash and 520 KB SRAM, as well as WiFi and Bluetooth communication. DFrobot DFR0654-F

Espressif ESP32-C3 WiFi module board. It offers 4 MB of Flash memory and 400 kB of SRAM, as well as an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5700

MPLAB PICkit Basic – Affordable programmer/debugger for PIC, AVR, dsPIC, and ARM Cortex microcontrollers with USB-C and SWD support. Microchip PG164110

Set of "sleeping lion" with the educational module micro: bit. It consists of a main plate, noise: bit and felt elements, thread and needle to create the toy. Pimoroni PIM363

Module with 17x7 LED matrix display (119 LEDs) designed to work with micro:bit. It uses the IS31FL3731 driver and communicates via the I2C interface. Pimoroni PIM353