Category: STARTER KITS, PROGRAMMERS, MODULES

The SparkFun Electric Imp imp002 Breakout allows you to explore the capabilities of the Imp product line in an easy to use package. The imp002 is actually a solder-down module version of the original Imp card. BOB-12958

Module with a miniature DC motor. No additional controller is required to start the engine. The module is controlled by the PWM signal. DFRobot DFR0411

Module with monostable relay. It allows you to control high-power elements with a microcontroller. Adafruit 2895

compact, battery-powered prototyping platform for rapid development of IoT solutions with support for LTE-M, NB-IoT, GNSS, Bluetooth LE, and NFC. Equipped with the nRF9160 SiP module, environmental sensors, and an asset tracking application, it is ideal for Proof-of-Concept and demonstrations. It includes a global eSIM with free data, and support for the nRF Connect SDK and nRF Cloud platform. Nordic Semiconductor THINGY91X

Development board specially designed to add advanced hardware I/O capabilities to your Android or PC application; PIC microcontroller connects an app on your PC or Android device to low-level peripherals like GPIO, PWM, ADC, I2C, SPI, and UART. DEV-13613

7-segment display controller, allowing communication over the I2C bus. Allows you to limit the pins needed to control the display. Adafruit 3088

X-NUCLEO-IDS01A4 is a development board STM32 Nucleo that allows the use of the RF SPSGRF-868 module for the ISM band (868 MHz carrier).

Module with a GPS receiver based on the MTK3333 system. Dedicated to Feather plates, communicates via the UART interface. Adafruit 3133

Advanced development kit for building IoT applications using LTE-M, NB-IoT, GNSS and DECT NR+, based on the nRF9151 SiP module with global LTE band coverage and built-in antennas. The board offers a rich set of interfaces, compatibility with the Arduino Uno form factor, a built-in SEGGER J-Link debugger and support for various SIM card formats, including Software SIM. The kit also includes a Serial LTE Modem application and full Nordic SDK support, which allows for a quick start and efficient development of IoT projects. Nordic Semiconductor nRF9151-DK

IoT development board the size of Arduino, equipped with an ARM Cortex-M3 processor (STM32F205) and a Wi-Fi communication module (with an integrated antenna and uFL connector). SparkFun DEV-13321

Development kit with SAMD21G18 microcontroller with ARM Cortex M0 core and LoRa RFM95 868/915 MHz radio communication module. Adafruit 3178

Module with ATSAMD21G18 microcontroller and 900 MHz wireless transceiver. The module can be used for transmission in the ISM 868 MHz band after the appropriate software configuration. The ATSAMD21G18 microcontroller (ARM Cortex-M0) is clocked at 48 MHz and operates at 3.3 V. Adafruit 3176

Gravity: Voice Recorder Module is a sound recording module powered by 5V voltage. It can store sounds up to 10 seconds long. DFRobot SEN0197

WiFi wireless communication module compatible with the pin spacing of XBEE modules. The module is powered by 3.3 V. The product is compatible with Arduino. DFRobot TEL0092

Gravity: Heart Rate Monitor Sensor is a sensor used to measure heart activity. Adapted for easy use with Arduino. SparkFun SEN0213

Module with monostable relay. It allows you to control high-power elements with a microcontroller. Adafruit 3191

Teensy Prop Shield is meant for making light and sound effects on small, handheld props and wearable costumes. This shield features a 2W audio amp, high-speed 5V buffers for driving APA102 LEDs, and an 8MB flash memory. PJRC PROP-SHIELD-LC

Feather board will let you integrate packetized radio (with the RFM69 radio) or LoRa radio (with the RFM9x\'s). These radios are good options for kilometer-range radio, and paired with one of our WiFi, cellular or Bluetooth Feathers, will let you bridge from 433/900MHz to the Internet or your mobile device. Adafruit 3230

These add-ons for any Feather board will let you integrate packetized radio (with the RFM69 radio) or LoRa radio (with the RFM9x\'s). These radios are good options for kilometer-range radio, and paired with one of our WiFi, cellular or Bluetooth Feathers, will let you bridge from 433/900 MHz to the Internet or your mobile device. Adafruit 3232

ESP32-S3-USB-OTG board with Wi-Fi, BLE, and USB-OTG for creating modern IoT projects and USB devices. Espressif ESP32-S3-USB-OTG