Category: STARTER KITS, PROGRAMMERS, MODULES

Module with a bistable button and red LED backlight. The board is equipped with a Gravity connector and communicates via a digital interface. DFRobot DFR0785-R

Adafruit 640 - Stainless Thin Conductive Thread - 2 ply - 23 meter/76 ft

A tool for debugging and programming STM32 microcontrollers via JTAG/SWD interfaces. It has a built-in current measurement unit (SMU) designed to optimise power consumption. STMicroelectronics STLINK-V3PWR

Audio module with loudspeaker designed to work with micro:bit. There is an amplifier and an 8 Ω 2 W speaker on the board. Pimoroni PIM356

The module is equipped with two buttons in red and blue. It communicates via a digital interface and allows you to add simple controls to your M5Stack based project. M5Stack U025

Set of "sleeping lion" with the educational module micro: bit. It consists of a main plate, noise: bit and felt elements, thread and needle to create the toy. Pimoroni PIM363

ATOM Lite development kit complete with microSD card reader up to 16 GB. M5Stack K044

Module with 17x7 LED matrix display (119 LEDs) designed to work with micro:bit. It uses the IS31FL3731 driver and communicates via the I2C interface. Pimoroni PIM353

This development board combines Wi-Fi, Bluetooth, and LoRa technologies, ideal for IoT projects requiring long-range communication. Equipped with a dual-core 240 MHz processor and an 868 MHz SX1262 modem, it provides a transmission range of up to several kilometers with low power consumption. It features a built-in 0.96-inch OLED display, a CP2102 USB-to-UART converter, and a lithium battery charging circuit for mobile operation. Heltec Lora32-V3

Module with an analog TEMT6000 light intensity sensor. The voltage at the output is linearly correlated with the intensity of the incident light. The module is supplied with the voltage from 3.3 to 5V. DFRobot SEN0043

Module with green LED diode and potentiometer. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 104030007

Module with a joystick with two analog axes (X and Y axis) with a button (Z axis). The board is equipped with a Grove connector and has analog outputs. Seeed Studio 101020028

Module with MQ5 LPG concentration sensor. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020056

STM32L152D-EVAL is an advanced evaluation kit with the STM32L152ZDT6 microcontroller, integrating a wide range of peripherals and displays. It enables full testing of the chip’s capabilities and the development of low-power applications with access to multiple communication interfaces and diagnostic tools.

The module with six touch buttons and LED diodes is designed for micro:bit. It uses the CAP1166 driver and communicates via the I2C interface. Pimoroni PIM401

Development kit from the M5Stack series equipped with the ESP32-S3 module. It will work well in projects related to IoT or in "wearable" devices. M5 Stack C124

Module with an analog MQ7 carbon monoxide sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0132

GPS module with SAM-M10Q GNSS receiver. The chip can receive data from all major positioning systems: GPS, GLONASS, Galileo, QZSS and BeiDou. It has derived UART and I2C interfaces. SparkFun GPS-21834

Module with a digital temperature and humidity sensor based on the SHTC3 system. Communication takes place via the I2C interface. SparkFun SEN-16467

The MicroMod main module with the STM32WB5MMG microcontroller, which allows communication under the Bluetooth Low Energy 5.3, Zigbee and OpenThread protocols. It is equipped with an M.2 connector and can work with MicroMod expansion boards. SparkFun DEV-21438