Category: STARTER KITS, PROGRAMMERS, MODULES
Kamami.pl electronics store offers a wide range of starter kits for microcontrollers and programmable devices as well as accessories (programmers, modules, etc.).
Subcategories
-
Atmel SAM
-
Atmel Xplain
-
AVR
-
DFRobot FireBeetle
-
ESP32
-
ESP8266
-
Feather / Thing Plus
-
Freedom (Kinetis)
-
Coral
-
Nordic nRF
-
M5Stack
-
Micro:bit
-
Peripheral modules
-
Particle Photon
-
PIC
-
Segger programmers
-
Universal programmers
-
Raspberry Pi RP2040
-
RFID
-
RISC-V
-
Seeed Studio LinkIt
-
Sparkfun MicroMod
-
STM32
-
STM32 MP1
-
STM32 Discovery
-
STM32 Nucleo boards
-
STM8
-
Teensy
-
WRTNode
-
XIAO/Qt PY
-
Other development kits
-
SOFTWARE
There are 2424 products.
Module with red LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0031-R
Prototype kit for use in industry. It includes a prototype board with an M-BUS connector, TTL-RS485 converter, connectors and a DIN rail. M5Stack Base26
Module with white LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0031-W
Module with yellow LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0031-Y
Extension module for STM32 Nucleo based on a two-channel SIO transceiver and IO-Link PHY L6364Q with built-in voltage stabilizers and a DC-DC converter. STMicroelectronics X-NUCLEO-IOD02A1
Knit conductive 100% silver fabric with resistance of less than 1 ohm per foot in any direction across the textile. Great for use with FLORA. 20 cm x 20 cm piece. Adafruit 1167
Module with an IO pin expander based on the TCA9534 system. It allows you to add 8 GPIO pins to an I2C-controlled project. SparkFun DEV-17047
The IO expansion module is designed to work with the micro:bit educational board. There are 20 GPIO pins on the board, a buzzer and a voltage stabilization circuit
Lipo battery with a capacity of 750 mAh for the M5Stack sets. Modules can be connected in parallel and stacked. M5Stack M002
Module with 6-axis BMI160 motion sensor (accelerometer and gyroscope) with 16-bit data resolution. It is supplied with the voltage in the range from 3.2 to 6 V. I2C communication. DFRobot SEN0250
Module with a buzzer (without generator) controlled by a digital interface. It allows you to generate simple sounds by changing the frequency of the control signal. DFRobot DFR0032
Module with an analog MQ4 methane sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0129
Module with a button, LED diode and a white cap. DFRobot DFR0029-W
A module with a joystick designed for M5Stack sets. Returns data from two axes and button state via the I2C interface. M5Stack U024-C
Module with a soil moisture sensor for the M5Stack sets. It has an analog output and a digital output with adjustable reaction threshold. M5Stack U019
Flash Programmer for ARM and Cortex cores, Segger
The infrared distance sensor enables the detection of objects in the range from 3 to 50cm. The sensor has a digital output, the detection threshold is adjusted by a potentiometer. DFRobot SEN0164
Keyboard module with five colored buttons. The board is equipped with a Gravity connector and has an analog output. Powered with the voltage of 3.3 V or 5 V. DFRobot DFR0075