Category: STARTER KITS, PROGRAMMERS, MODULES

Starter kit from NXP Semiconductors (formerly Freescale Semiconductor) based on the Kinetis KE06Z microcontroller with an Arm Cortex-M0+ core and 5V supply, featuring CAN and IrDA interfaces, a temperature sensor, and an integrated OpenSDA programmer/debugger. FRDM-KE06Z

Starter kit from NXP Semiconductors (formerly Freescale Semiconductor) based on the Kinetis K64 microcontroller with an Arm Cortex-M4 core, featuring an Ethernet interface, microSD card slot and an integrated OpenSDAv2 programmer/debugger. FRDM-K64F

ATATMEL-ICE-BASIC is a programmer designed to work with AVR microcontrollers with the On-Chip Debug function and microcontrollers with the ARM Cortex-M core from Atmel. Available interfaces are JTAG, SWD, PDI, TPI, aWire, SPI and debugWire.

Atmel starter kit with ATmega168 microcontroller and debugger (JTAG / USB) co-operating with Atmel Studio from 6.2.

Module with a deflection sensor with two measuring probes. The board houses the ADS1015 converter, which is an ADC converter with an output in the form of an I2C interface. SparkFun SEN-14666

Module with a 4-inch touch display that uses two MCU systems (ESP32-S3 and RP2040) and supports Wi-Fi and BLE communication. The board is equipped with USB Type C, I2C (Grove) and analog inputs interfaces and can easily connect to other peripheral devices. Seeed Studio 114993068

High temperature measuring kit. It consists of a signal conversion module with a range of -270°C to 1372°C and a K-type thermocouple probe with a range of up to 800°C. I2C communication DFRobot DFR0558

Edge Breakout for micro: bit is an expansion board for the micro: bit module. It offers leaded I / O pins on a 3 x 25 pin gold pin connector. There are available anlog entries, GPIO pins, I2C and SPI interfaces, as well as power pins. Edge Breakout for micro: bit

Development kit with STM32F105RBT6 microcontroller (128 KB Flash, 64 KB RAM) and L6470 stepper motor driver

Flash memory programmer for systems with ARM7/9/11, Cortex, RX and PPC cores. It is equipped with 2 GB of internal memory allowing for storing large amounts of data and configuration files. Segger Flasher PRO XL (5/17/02)

The Segger J-Link USB Isolator (8.07.02) provides isolation up to 3 kV DC and supports USB Full-Speed transmission with a maximum output current of 200 mA. The device is equipped with short-circuit protection and LED indicators for power status and overload.

Module with 16 RGB LEDs WS2813 Mini. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 104020171

Module with an infrared sensor MLX90640 - a measuring matrix with a resolution of 32x24 pixels. It offers an accuracy of 1.5°C and a viewing angle of 55x35°. Communication with the sensor takes place via the I2C interface. SparkFun SEN-14844

embOS designed for ARM7/9 and KEIL compiler

Module with NEO-F9P GNSS receiver. It allows you to track signals from several satellite systems, including GPS, GLONASS, Galileo and Beidou, and offers accuracy of up to 10 mm using an RTK base station. It offers five communication ports: USB type C, UART1, UART2 for RTCM, I2C and SPI reception and Qwiic connectors. SparkFun GPS-23288

embOS designed for ARM7/9 and KEIL compiler

Module with a motion sensor that uses the Doppler effect to detect moving objects using microwaves. It is powered with the voltage of 5 V and has a digital output (Gravity connector). DFRobot SEN0192

A board with an ESP32 module equipped with a 1.28-inch round display. It offers Wi-Fi and Bluetooth 5.0 communication and has a built-in 6-axis QMI8658 IMU sensor and supports charging lithium batteries. Perfect for developing IoT, mobile devices and wearable electronics projects. Waveshare ESP32-S3-LCD-1.28