Core407Z development kit with STM32F407ZET6 - Waveshare 6446

Description

A startup kit with a microcontroller from the STM32F407ZE family (ARM Cortex-M4 core). It is equipped with the basic components needed to run the chip, as well as configuration switches and a reset button. The user has all the pins of the chip routed out to pin connectors with a raster of 2.54 mm. It is powered via a mini-USB connector and programmed via a JTAG or SWD interface. No programmer is included on the board, so the kit requires an external programmer/debugger. Full documentation is available on the product page.

1. STM32F407ZxT6 (STM32F407ZET6 by default):the high performance STM32 MCU which features:
   • Core: Cortex-M4 32-bit RISC
   • Feature: a full set of single-cycle DSP instructions
   • Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz
   • Operating Voltage: 1.8V-3.6V
   • Package: LQFP144
   • Memories: 512kB/1024kB Flash, 192+4kB SRAM
   • MCU communication Interfaces:
     • 3 x SPI, 4 x USART, 2 x UART, 2 x I2S, 3 x I2C
     • 1 x FSMC, 1 x SDIO, 2 x CAN
     • 1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY
     • 1 x 10/100 Ethernet MAC
     • 1 x 8 to 14-bit parallel camera interface
   • AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)
   • Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP
2. AMS1117-3.3 (on bottom side): 3.3V voltage regulator
3. MIC2075 (on bottom side): onboard USB power management device
4. Power supply switch, powered from 5Vin or USB connection
5. Boot mode switch, for configuring BOOT0 pin
6. Power indicator
7. VBUS LED
8. Reset button
9. 8M crystal oscillator (on bottom side)
10. 32.768K crystal (on bottom side), for internal RTC with calibration
11. JTAG/SWD interface: for debugging/programming
12. USB interface
    • as DEVICE, used for establishing USB communication between PC and the STM32 development board
    • as HOST, connecting to USB devices such as USB flash drive through a USB OTG cable
13. MCU pins expander, VCC, GND and all the I/O ports are accessible on expansion connectors for further expansion
14. 5Vin pinheader, 5V power supply is required when using USB HOST/OTG
15. USB HOST/OTG jumper
    • short the jumper when using USB HOST/OTG
    • open the jumper to disconnect from I/O port
16. VBAT selection jumper
    • short the jumper to use system power supply
    • open the jumper to connect the VBAT to external power, such as battery
17. VREF selection jumper
    • short the jumper to connect VREF+ to VCC
    • open the jumper to connect VREF+ to other custom pin via jumper wire

Features

• STM32F407ZE microcontroller
• Configuration switches and jumpers
• MiniUSB power connector
• Power LED
• SWD and JTAG interface
• Reset button
• 3.3V stabilizer
• Dimensions: 68.5 x 55.88 mm

Kit contains

• Core407Z module
• MiniUSB cable