Category: STARTER KITS, PROGRAMMERS, MODULES

Adafruit HUZZAH32 is a development board with a built-in WiFi ESP32 module. Processor frequency: 240 MHz, the module has a built-in system for charging Li-Pol batteries. The plate has soldered goldpin connectors (female extension). Adafruit 3619

Portable Flash programmer for built-in and external flash memory. Segger Flasher Portable PLUS

The module is equipped with three RGB SK6812 LEDs. It is designed to work with the M5Stack sets. Communicates via a single-wire digital interface. M5Stack U003

Miniature pressure measurement module equipped with a 25 psi piezoresistive pressure sensor. It allows you to perform calibrated and compensated pressure measurements from 60 mbar to 2.5 bar. SparkFun SEN-16476

Module with an analog MQ4 methane sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0129

The STEVAL-FKI433V2 evaluation board is based on the S2-LP sub-1GHz ultra-low power low data-rate transceiver suitable for ISM bands and wireless M-Bus. The NUCLEO-L053R8 motherboard is equipped with an STM32L0 low power microcontroller to control the S2-LP

Set with mini propeller, DC motor and module with motor controller. Allows you to build a mini fan with speed control. Seeed Studio 108020021

Module with an analog sensor of carbon monoxide and combustible gases (methane, propane) MQ9. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0134

Module with SHT31 temperature and humidity sensor. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020212

Module with LSM6DS3 sensor that combines a 3-axis accelerometer and a 3-axis gyroscope. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 105020012

Development board 1GHz AM4378, 512MB DDR3, 4GB eMMC, Industrial. MYD-C4378-4E512D-100-I

Module with a MLX90641 thermal imaging camera with a 16x12 field matrix and a 110° viewing angle. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020892

12-bit DAC converter module designed to work with the M5Stack sets. It enables the conversion of digital signals into an analog signal. M5Stack DAC Unit

Module with a pulse sensor (heart rate). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 103020024

Module with Grove connector equipped with AS5600 magnetic encoder with a resolution of 12-bit. It allows for non-contact measurement of the angle of rotation. The module has an analog/PWM output and an I2C interface. Seeed Studio 101020692

Module with an ambient oxygen concentration sensor. The system allows you to measure the oxygen volume in the range up to 25% with a resolution of 0.15%. The module communicates via the I2C interface. DFRobot SEN0322

Module with the MCP9600 amplifier designed to work with a K-type thermocouple. The module has a PCC connector for connecting this type of thermocouple. I2C communication. SparkFun SEN-16294

NXP MRB-KW019032EU is a modular set based on a 32-bit microcontroller with ARM Cortex M0 48 MHz core, equipped with an 868 MHz radio module. MRB-KW019032EU

Module with 16-channel PCA9685 servo driver designed for Raspberry Pi minicomputers. The board is equipped with a USB Type C power connector. SparkFun DEV-15316

SparkFun Qwiic kit. Contains 10 wires of different lengths and tips. It allows you to connect Qwiic modules to a programming platform or to a prototype board. SparkFun KIT-15081