IPS LCD display with a diagonal of 7" and a resolution of 1024x600 pixels, equipped with a capacitive touch panel. Communicates via the LVDS interface. Riverdi RVT70HSLNWC00

Gravity: Digital 10A Relay Module is a module with 10A 35VAC / 30VDC relay compatible with devices with control signals in the range of 2.8 ... 5.5V. DFRobot DFR0473

Pin header, 20 pin, 2,54mm

IPS LCD display with a diagonal of 7" and a resolution of 1024x600 pixels. Equipped with a 40-pin FPC connector. HDMI adapter included. Waveshare 70H-1024600-IPS-B

Module with 1.3 "OLED display with a resolution of 128 x 64 pixels, thanks to the SH1106 driver and communication via the I2C bus is an ideal solution to build a device with a spectacular appearance and reliable work

The Tic T825 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuration over USB using our free software. The controller supports six control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), quadrature encoder, and hobby radio control (RC). 

The RoboClaw Solo motor controllers from Basicmicro (formerly Ion Motion Control) can control a single brushed DC motor using USB serial, TTL serial, RC, or analog inputs. An integrated quadrature decoder make it easy to create a closed-loop speed control system. 

Small GPS location module with L80-39 GPS chip, USB and TTL two ports,easy to be used with Raspberry Pi, Arduino, STM32 and other kind of micrcontrollers. The GPS module uses NMEA0183 communication protocol, integrated ultra-small SMA antenna connector. DFRobot TEL0119

Module with a DC motor driver based on the MC33886 chip. It allows you to control the movement of drives with a working voltage from 5 to 28 V and a current of up to 5 A

Incremental encoder (horizontal) with a resolution of 15 pulses per revolution. Equipped with a switch

GEMMA M0 is an intelligent clothing controller from Adafruit. In relation to the classic GEMMA board, it was equipped with a 32-bit ATSAMD21E18 microcontroller (based on Cortex M0 +). It has GPIO pins, RGB DotStar diode. The board can be powered by a 3.7 V Li-Ion battery (JST connector). Adafruit 3501

Adapter from HDMI to VGA with microUSB power input and 3.5mm audio jack, 15cm

Electrochemical sensor that measures the concentration of ethyl alcohol in the air. The current flowing through the gas sensor is directly proportional to the gas concentration

Lever with Hall sensor and analog output. Used as a joystick in control panels

The RoboClaw Solo motor controllers from Basicmicro (formerly Ion Motion Control) can control a single brushed DC motor using USB serial, TTL serial, RC, or analog inputs. Pololu 3291

Module with a Panasonic sensor with an 8x8 IR thermal matrix (AMG8833 chip) with a built-in 3.3 V controller and a logic level translator. The I2C interface is used for communication. Adafruit 3538

Module with a matrix of 64 Hall sensors, which enables the conversion of magnetic fields into a visual spectrum. SparkFun SPX-14652

IPS LCD display with a diagonal of 7" and a resolution of 1024x600 pixels. Equipped with a 40-pin FPC connector. Waveshare 70H-1024600-IPS-A

Board with goldpin connectors designed for micro:bit sets. It enables connection of a micro: bit set and attaching a module with connectors, eg to a contact plate. Adafruit 3695

Micro:Mate is an expansion board for the micro: bit development module. It provides six 3-pin connectors with I/O outputs, a 3.5mm audio jack connector and is powered from a 5V microUSB connector. DFRobot DFR0518