Module with BME280 environmental sensor. It allows you to measure temperature, humidity and pressure. The sensor is equipped with two communication interfaces: SPI and I2C. SparkFun SEN-13905

Module with a color LCD IPS display with a screen diagonal of 4" and a resolution of 800x480 px, dedicated to the Raspberry Pi. It communicates via the DSI interface. Pimoroni PIM370

Module with 13 QTR type optocoupler with analog output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 40 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4253

HDMI cable compliant with the HDMI High Speed with Ethernet specification, allows you transmit a 4k resolution image at 30 Hz, 3 m cable length. LANBERG

ToF distance sensor (Time of flight) with a range of up to 5 m. The module is supplied with the voltage of 3.3 V and communicates via the I2C interface. SparkFun SEN-19036

Module with e-Paper display with a diagonal of 2.9" and a resolution of 296x128 px. Communication via the SPI interface. Waveshare Pico-ePaper-2.9 

MP3 panel with a HiFi amplifier for installation in an audio device. It allows you to play files from USB memory, SD card, via AUX and Bluetooth. It has a built-in FM receiver

This compact breakout board for Maxim’s MAX14870 motor driver offers a wide operating voltage range of 4.5 V to 36 V and can deliver a continuous 1.7 A (2.5 A peak) to a single brushed DC motor. It features a simple two-pin speed/direction interface and built-in protection against reverse-voltage, under-voltage, over-current, and over-temperature.

7" LCD display with capacitive touch screen. The display is equipped with HDMI interface for image display and USB for touch screen. It has a resolution of 1024x600 pixels. DFRobot DFR0506

The driver with the TPIC6C596 system allows you to control 7-segment displays using three signal lines. Serial connection of controllers is possible. SparkFun WIG-13279

1m USB-A to microUSB cable. The cable has a detachable tip with a magnetic holder, LED indicator. It can charge the device with voltage up to 5V and 3A.

Module with 7 QTR type optocoupler with RC (digital) output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 40 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4147

The adapter allows you to connect a device with DisplayPort mini slot to the HDMI port. Compatible with Thunderbolt connector. LANBERG AD-0005-BK

Cable dedicated to MyoWare 2.0 muscle tension sensors. It allows you to connect the electrode with the plate in the event that it must be located at a distance from the sensor. SparkFun CAB-19244

BME688, 4-in-1 air quality sensors, gas, humidity, pressure and temperature sensor, LGA-8

A set of 175 connectors in a plastic box for cables with a diameter of 1.25-4mm. The set contains various types of terminals, among others ring, fork or clamping. Lanberg CC01-BCC-IT175

32-bit MCU for automotive applications, Power Architecture (e200z0h), 1024 kB Flash, LQFP100, STM, RoHS

2.4 "TFT LCD touch screen with 320x240 pixel resolution, ILI9341 display controller (SPI interface). The module is additionally equipped with a micro-SD card slot. Adafruit 2478

Knit conductive 100% silver fabric with resistance of less than 1 ohm per foot in any direction across the textile. Great for use with FLORA. 20 cm x 20 cm piece. Adafruit 1167

Module with 3.5 mm TRS connector for MyoWare 2.0 muscle tension sensors. It allows you to conveniently connect the sensors with the development board via the Arduino shield. SparkFun DEV-18425