The Hantek PP-300 is an oscilloscope probe with a bandwidth of 300 MHz, designed for precise measurement of high-frequency signals. It is compatible with a wide range of digital and analog oscilloscopes and features a switchable attenuation setting between 1× and 10×, allowing flexible adaptation to various applications. Thanks to its ergonomic design and robust construction, the probe offers user comfort and durability for everyday use in laboratory environments.

The Zeenko 30 dB SMA attenuator is a solid and precise component for RF measurement paths, useful in diagnostics, calibration and protecting devices such as the tinySA, nanoVNA or RF generators. It enables safe measurements and improves impedance matching quality over a wide frequency range.

Oscilloscope probe designed to analyze signals generated by the ignition coil in car engines. It is compatible with most digital oscilloscopes. Hantek HT20COP

Oscilloscope Probes (pair). 460-004

Universal oscilloscope probe with BNC plug and 10:1 voltage divider. It has a frequency range of 60 MHz and allows you to perform measurements with a maximum voltage of up to 600 V.

This active measurement probe is designed for precise analysis of ripple, noise, and rapid changes on DC power lines, particularly in systems requiring high power integrity. The device offers a bandwidth of up to 2 GHz and a wide operating range, enabling accurate measurements of very small amplitude signals with minimal load on the system under test. With an SMA interface, 5V USB-C power supply, and a low current consumption of 20 mA, the probe easily integrates with test benches and oscilloscopes. PRP1 Power Rail Probe v2.0

Micsig MDP series differential probe based on advanced SigOFIT technology. It offers a frequency band of 200 MHz and the ability to measure voltage up to 700 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig DP702

High-voltage differential probe. It has good measurement characteristics: a bandwidth of 50 MHz and an operating voltage of up to 1300 V. The probe has two attenuation coefficients: 50X and 500X. Hantek HT8050

Micsig MDP series differential probe based on advanced SigOFIT technology. It offers a frequency band of 500 MHz and the ability to measure voltage up to 1500 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig MDP1505

High-voltage oscilloscope probe with BNC connector and 100:1 voltage divider. It has a frequency response of 100 MHz and allows measurements with a maximum voltage of up to 2 kV. Hantek T3100

A 20:1 signal attenuator designed to assist in measuring automotive performance, including measuring fuel injector and primary ignition runs. Hantek HT201

Universal measurement probes for a multimeter. Compatible with all Micsig oscilloscopes. Micsig MS-A-005

An oscilloscope probe designed to analyze signals generated by the ignition coil in car engines. It is compatible with most digital oscilloscopes. Micsig MS-A-008

The P2150 oscilloscope probe with a 150 MHz bandwidth and BNC connector ensures high signal integrity and wide bandwidth, featuring switchable attenuation of 1X/10X and an input resistance of 1 MΩ/10 MΩ ±2%. The set includes accessories such as a compensation tool, identification rings, and a hook clip for easier use.

Micsig DP series differential probe based on advanced SigOFIT technology. It offers a 500 MHz frequency band and the ability to measure voltages up to 700 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig DP705

Probe for measuring AC currents up to 1000 A. It works in the range from 10 Hz to 100 kHz, it can be connected to the oscilloscope through the BNC connector. Micsig ACP1000

LCRkelvin is a four-wire Kelvin probe for precise measurement of RLC components with minimal wire resistance impact. Equipped with gold-plated Kelvin clips, it ensures accuracy and reliability, and its design is compatible with LCR meters from various brands, such as Hantek and Uni-T

Micsig differential probe from the DP series designed for high-voltage and differential signal measurements. Offers 100 MHz bandwidth and supports voltage measurements up to 700 V. Features a standard BNC connector and USB Type-C power supply. The current product revision includes a new enclosure with three function buttons. Micsig DP700

Micsig MDP series differential probe based on advanced SigOFIT technology. It offers a frequency band of 300 MHz and the ability to measure voltage up to 1500 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig MDP1503

Micsig DP series differential probe based on advanced SigOFIT technology. It offers a frequency band of 100 MHz and the ability to measure voltage up to 3000 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig DP3000