.png)
Category: Main categories
Subcategories
There are 23554 products.
Li-Po battery 3.7V / 750mAh, PCM protection, connector 2 pins, cable length 150mm. Akyga AKY0155 - LP403450
Male terminal block, angled, 12-pin. Pitch 5.0mm. Height 7.8mm. 2EDGRC-5.0-12P. Set of 5 pieces
2.9" e-Paper display with 296x128 px resolution, Red/Yellow/Black/White colors, 3-wire and 4-wire SPI interface, 3.3 V operating voltage, passively reflective without backlight, ultra-low power consumption. Waveshare 2.9inch e-Paper (G)
The Lanberg Cat. 8.1 patch cord with Fluke Passed certification guarantees top quality and reliability, enabling optimal network connections compatible with various networking devices in any environment. Lanberg PCF8-10CU-0025-W
Expansion module for Flipper Zero (not included) designed for voltage and frequency measurement, waveform observation and detection and control of I2C and SPI devices. Provides Scope, Probe, I2C Probe and SPI Probe functions, along with feedback using sound, vibration and an RGB LED. The voltage measurement range is 0 V to 12 V, while frequencies can be measured up to approximately 200 kHz. DigiLab
SenseCAP Watcher is a device based on ESP32S3 and AI chip Himax WiseEye2 HX6538, which combines advanced image processing with voice command recognition. With a camera, microphone, speaker and support for LLM technology in SenseCraft, it is ideal for monitoring spaces, interacting with users and integrating with IoT systems. Seeed Studio 113991315
A 3.2" TFT touch LCD module with a resolution of 320x240 pixels. It uses a 16-bit parallel interface for the image display and SPI for the touch panel. Waveshare 3.2inch 320x240 Touch LCD (D)
A 12MP camera with a USB 2.0 interface. Equipped with a sensor with a 110° wide-angle lens and a microphone. ArduCAM B0433
Mini SPDT type end switch with lever length 13.5mm and current capacity of 1A contacts. Pololu 1528
Breadboard power supply module with a 5V USB-C input and 12V DC jack. Independently selectable outputs provide 12V or 3.3V on VOUT1 and 5V or 3.3V on VOUT2. Features a power switch, power indicator LED, and automatic input source selection. Soldered 333084
MCP4018 digital potentiometer module with 10kΩ nominal resistance and 128 adjustment steps. I2C control enables software-based resistance adjustment, while two Qwiic connectors simplify integration with compatible boards. Designed for adjusting signal levels and analog circuit parameters from a microcontroller. Soldered 333091
Digital oscilloscope with built-in signal generator. It has two measurement channels with 150 MHz bandwidth and a single-channel signal generator with waveform frequencies up to 25 MHz. Hantek DSO2D15
Male terminal block, angled, 5-pin. Pitch 3.5mm. Height 9.2mm. KF2EDGR. Set of 10 pieces
Step-Up DC-DC converter module. It has an input voltage of 1.3 to 16 V, an output voltage of 12 V and a maximum input of up to 2 A. Pololu 4945
RA050-60 is a resettable PTC fuse with a hold current of 0.5 A and a maximum voltage of 60 V, designed to protect against short circuits and overloads. It is suitable for use in power supplies, audio circuits, alarm systems, and electronic devices, allowing repeated use without replacement.
Plastic housing dedicated to Raspberry Pi 5 minicomputers. It is made of durable plastic and has a nice black color and oval shape. It has a holder that allows you to mount a fan, so it can provide good cooling necessary in demanding applications
IOT.ZD3005 Pi5J ABS V0 - Din rail enclosure iot.ZD3005 pi5 lightgray ABS V0
A tip with a truncated tip designed for the TS100 and TS101 soldering irons. Miniware TS-C4