75:1 12V LP 25Dx54L- Metal Gearmotor

Description

This gearmotor consists of a low-power, 12 V brushed DC motor combined with a 74,83:1 metal spur gearbox. The gearmotor is cylindrical, with a diameter just under 25 mm, and the D-shaped output shaft is 4 mm in diameter and extends 12.5 mm from the face plate of the gearbox.

Features

• Supply voltage: 12 V
• Gear ratio: 74,83:1
• Speed: 71 RPM
• Maximum torque: 6 kg*cm
• Minimum current consumption: 0,1 A
• Maximum current consumption: 1,1 A
• Diameter: 124 mm
• Length: 54 mm
• Weight: 91 g

Supply voltage

Pololu 25D motors are available in two versions with the recommended voltage of 6 V and 12 V. These motors differ in power and current consumption. The power of LP motors in the 6 V and 12 V versions differs slightly, and the current consumed by the 12 V LP motors is more than half that of the 6 V LP motors. The power of the HP 12 V motors is noticeably greater than the HP 6 V, so the difference in the consumed current is not as big as in LP engines. It is possible to power the motors with a lower or higher voltage, but it is associated with lower power or a shorter life of the motors, respectively.

Dimensions and weight

All motors have the same dimensions. Depending on the gear ratio, the gears differ in length, as shown in the technical drawing below. The metal gear housing has two tapped holes for M3 screws. The gearmotors weigh from 60 g to 110 g depending on the gear size.

Dimensions of 25D motors in version with encoders (units in mm).
Dimensions of 25D motors without encoders (units in mm).

Magnetic encoder

All Pololu 25D gearmotors are available in versions with a magnetic encoder and without an encoder. The encoder is mounted on an additional shaft on the opposite side of the main shaft. The shaft on which the encoder is mounted is led directly from the motor (without gear), which allows the installation of the encoder which works much more accurately than if it was mounted on the shaft behind the gear. The use of an encoder allows to determine the speed and position of the motor shaft and to apply these values in the PID controller feedback loop.

Single-sided shaft motor	Motor with double-sided shaft and mounted encoder	A motor with a double-sided shaft, an encoder and a removed plastic cover

Using the encoder

A two-channel Hall effect encoder is used to sense the rotation of a magnetic disk on a rear protrusion of the motor shaft. The quadrature encoder provides a resolution of 48 counts per revolution of the motor shaft when counting both edges of both channels. To compute the counts per revolution of the gearbox output, multiply the gear ratio by 48. The motor/encoder has six color-coded, 8″ (20 cm) leads terminated by a 1×6 female header with a 0.1″ pitch, as shown in the main product picture. This header works with standard 0.1″ male headers and our male jumper and precrimped wires. If this header is not convenient for your application, you can pull the crimped wires out of the header or cut the header off. The following table describes the wire functions.

Color Function Red motor power (connects to one motor terminal) Black motor power (connects to the other motor terminal) Green encoder GND Blue encoder Vcc (3.5 V to 20 V) Yellow encoder A output White encoder B output
	Encoder A and B outputs for 25D mm HP 6V metal gearmotor with 48 CPR encoder (motor running at 6 V).

Wheels

The 4 mm diameter gearbox output shaft works with Pololu universal aluminum mounting hub for 4mm shafts, which can be used to mount our larger Pololu wheels (60mm-, 70mm-, 80mm-, and 90mm-diameter) or custom wheels and mechanisms to the gearmotor’s output shaft as shown in the left picture below. Alternatively, you could use our 4mm scooter wheel adapter to mount many common scooter, skateboard, and inline skate wheels to the gearmotor’s output shaft as shown in the right picture below.

Black Pololu 80x10mm wheels	White Pololu 80x10mm wheels	Black Pololu 80x10mm wheel with motor mounted
Wild Thumper wheels Chrome	Wild Thumper wheels red matalic	Wild Thumper wheel with engine mounted
Black scooter/skate wheels with 200 mm, 144 mm, 100 mm, 84 mm, and 70 mm diameters.		Aluminum Scooter Wheel Adapters

Brackets

The gearmotor face plate has two mounting holes threaded for M2.5 screws, and you can use our custom-designed 20D mm metal gearmotor bracket (shown in the left picture below) to mount the gearmotor to your project via these mounting holes and the screws that come with the bracket.

Brackets for 25D engines	25D engine with attached bracket and adapter	25D engine mounted on a platform with a Scooter wheel

Motor controllers

We have a number of motor controllers and motor drivers that work with these 20D mm metal gearmotors. In particular, we recommend MC33296-based motor drivers, for which we have basic single and dual carriers and a dual-channel shield for Arduino.

RoboClaw 2x7A Motor Controller (V5B)	Pololu Dual VNH5019 Motor Driver Shield for Arduino	Jrk G2 24v13 - DC motor controller

Current sensors

We have an assortment of Hall effect-based current sensors to choose from for those who need to monitor motor current:

Current sensor module (0-20A) with ACS712-20	ACHS-7124 Current Sensor Carrier ±40A	Pololu 2452 - ACS711EX Current Sensor Carrier -15.5A to +15.5A

Types and parameters of 25D Pololu engines:

Our offer includes motors with gear ratios from 4.4: 1 to 499: 1, with a rated voltage of 6 V and 12 V. All variants of motors with gears are available with and without a magnetic encoder. In addition, gearedless encoder motors are available to fit gears from the rest of the 25D motors.