

zł1,267.90 tax excl.
A device that provides electrical isolation between the J-Trace emulator and the ARM board, which protects against electrical interference, especially in systems where the development tools and the application do not share the same ground. It provides 1 kV DC isolation, supports trace frequencies up to 75 MHz, and is compatible with J-Trace V2 and later versions, with a minimum power consumption of 25 µA. Segger J-Trace Isolator (07/08/10)
J-Trace Isolator is a device that provides electrical isolation between the J-Trace emulator and any ARM board using the standard 19-pin Cortex-M connector. The J-Trace Isolator ensures high-quality trace signals while protecting against electrical interference. This solution is essential when development tools are not connected to the same ground system as the application, such as in motor control systems.
The device offers 1 kV DC electrical isolation and supports a variety of applications in product development involving sensors or other analog circuits. The J-Trace Isolator protects the target equipment from electrical disturbances originating from the development computer. It is compatible with J-Trace V2 and newer versions. The device is powered by the emulator, and the power consumption from the target device is only 25 µA. It uses a standard 19-pin JTAG connector and supports frequencies up to 75 MHz for trace, 50 MHz for JTAG, and 4 MHz for SWD.
How to Use J-Trace Isolator with J-Trace PRO
The J-Trace Isolator is designed for use with J-Trace V2 and newer versions, but can also be used with other ARM emulators with the same pinout. In such cases, ensure that 5V is supplied to pin 19 of the emulator's connector, and that the emulator is protected from damage when 5V is applied to this pin. Use of this solution is at your own risk!
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
J-Trace PRO for Cortex-M is setting a new standard for trace probes. It enables continuous streaming trace via its Gigabit Ethernet interface, lifting the limitations by internal buffers and slow data transmission. (j-trace-pro)
An advanced device that allows you to track and analyze real-time code executed on a core with Cortex-A, Cortex-R and Cortex-M. Segger J-Trace PRO for Cortex (8.20.00)
No product available!
An advanced device that allows real-time tracking and analysis of code executed on a RISC-V core chip. Segger J-Trace PRO for Cortex (8.20.00)
No product available!
Advanced code analysis and embedded debugging probe featuring real-time streaming tracing, Live Code Profiling, and Live Code Coverage. Supports a wide range of architectures including Arm, RISC-V, and Renesas RX, and features USB 3.0 and Gigabit Ethernet for fast data transfer and reliable operation. Segger J-Trace PRO (8.24.00)
No product available!
10-pin Needle Adapter to connect Flasher 5, Flasher ST7 or Flasher STM8 to a PCB, Segger
No product available!
Adapter that enables JTAG connection between devices such as J-Link, J-Trace or Flasher and Jacinto7 systems from TI, offering access to JTAG/SWD and Trace connectors with TPIU tracking function. Thanks to high quality of workmanship and versatility, the adapter provides a stable connection, supporting debugging, testing and diagnostic processes in embedded systems. Segger MIPI-60 Adapter (8.06.42)
No product available!
The Segger J-Link Supply Adapter (8.06.14) allows you to manually set the debug probe I/O voltage, preventing damage to the target board, adjustable from 1.2V to 5.0V. It can be inserted between J-Link or Flasher and the target device, reducing the number of connections needed, which is especially useful in a production environment.
Power adapter providing a stabilized 5V supply voltage for the target board. Segger 5V Target Supply Adapter (8.06.29)
No product available!
RS232 module used as a communication extension equipped with a female DSUB9 connector, allowing easy connection to a PC or USB-RS232 adapter. Segger emPower RS232 Add-On (6.32.32)
No product available!
Xilinx adapter that connects to Xilinx\'s 14-pin, 2mm JTAG connector, providing debugging of MCU cores such as the Arm Cortex-A9 on Xilinx Zynq FPGAs. With its compact design and high signal quality, it is a reliable tool for engineers working with FPGA platforms. Segger Xilinx Adapter (06/08/19)
No product available!
The RX FINE adapter converts a standard 20-pin 2.54 mm connector to a 14-pin 2.54 mm connector. It enables the connection of Segger programmers with RX devices from Renesas. Segger RX Fine Adapter (8.06.10)
No product available!
Standard 20-pin 0.1 male connector to provide electrical isolation, Segger
The Intel FPGA Adapter (formerly J-Link Altera Adapter) connects to the Intel FPGA 10-pin JTAG connector, enabling debugging of FPGA-based MCU cores such as the dual-core Arm Cortex-A9 in Cyclone V devices. on Intel FPGA solutions.
No product available!
An advanced tool that enables the integration of J-Link support into your own applications, used in both development environments and custom production tools. Supports debugging, flash programming, and application testing, offering support for Windows, Linux, and macOS, as well as compatibility with many programming languages via a DLL or shared library. Segger J-Link SDK (08.08.06)
No product available!
An adapter to connect the JTAG to a target hardware system that has an automotive connector. It has a 20 pin 2.54mm JTAG connector and a 19 pin 1.27mm Samtec FTSH connector. Segger Infineon AUTO-20 Adapter (8.06.33)
No product available!
Adapter that enables JTAG connection between Flasher programmer and target hardware with Power Architecture or PowerPC microcontrollers. Converts 20-pin 0.1\'\' connector to 14-pin JTAG, ensuring compatibility, stability and secure connection. Segger PPC 14-Pin Adapter (06.08.07)
No product available!
Segger adapter 8.06.28 allows conversion from a 20-pin 0.1" connector to a 10-pin 0.05" Cortex-M type connector with the option of custom pin mapping. A useful solution for integrating programmers and debuggers with devices featuring different pin configurations.
The Segger J-Link Signal Smoothing Adapter (8/06/12) is designed to improve signal integrity between the J-Link debug probe and the target debug device. It allows JTAG signals to be suppressed by adjustable series resistors, preventing excessive gain and jitter.
No product available!
The Segger J-Link USB Isolator (8.07.02) provides isolation up to 3 kV DC and supports USB Full-Speed transmission with a maximum output current of 200 mA. The device is equipped with short-circuit protection and LED indicators for power status and overload.
No product available!
J-Link SDK one year Support and Update Agreement extension. Can only be purchased by customers with a J-Link SDK License (Model 8.08.06). Segger J-Link SDK Extension (8.08.18)
No product available!
A device that provides electrical isolation between the J-Trace emulator and the ARM board, which protects against electrical interference, especially in systems where the development tools and the application do not share the same ground. It provides 1 kV DC isolation, supports trace frequencies up to 75 MHz, and is compatible with J-Trace V2 and later versions, with a minimum power consumption of 25 µA. Segger J-Trace Isolator (07/08/10)