Best sellers

Arty S7-25 is a development kit with Xilinx FPGA XC7S25-CSGA324. The board has many peripherals: slide switches, monostable buttons, RGB LEDs etc. Digilent (410-352)

Antistatic, bactericidal foam with active surfactant particles, removing impurities from all kinds of TFT liquid crystal displays. MICRO CHIP ELEKTRONIC ART. 013

Pmod I2S2 is a module with 24-bit A / C and D / C audio converters derived from standard 3,5 mm Jack connectors. Thanks to them, it is possible to send and receive stereo audio signals using the I2S protocol. Digilent 410-379

Arducam Nano RPI Module is a minicomputer equipped with Broadcom BCM2835 processor and VideoCore IV GPU. The module has two CSI connectors for connecting cameras, video output (PAL), SPI, I2C, UART, and GPIO. ArduCam B0101

AK-NB-01A is a solid 3-pin clover network cable of the Pro series, 1.5 m long. Designed to supply laptop adapters and all other IEC C5 compatible plugs. The cable is compatible with most power supplies available in our offer. Akyga AK-NB-01A

Charger module for two cells of Li-Ion batteries. It can charge with a current of up to 0.55 A with a charging voltage of 8.4 V. Powered by a USB type C connector

The Arducam Mini Multi-Camera Adapter Board is an expander that can connect up to 4 ArduCam cameras. ArduCam B0074

Wireless PS2 controller included with the receiver. It has a range of approx. 8 m and is powered by two AAA batteries. Communication via the SPI interface

ArduCam CSI to HDMI modules are designed to work with cameras: Raspberry Pi V1 and Raspberry Camera V2. ArduCAM CSI to HDMI allows you to extend the signal from cameras using the HDMI <-> HDMI cable (up to 10 meters). Arducam B0091

EEPROM memory in SOIC-8 package. The chip has 32 kb memory (4k x 8 bits). Communication takes place via the I2C interface. ON Semiconductor CAT24C32WI-GT3

Laser sensor of air pollution with PM2,5 and PM10 particles. It allows for precise analysis of the amount of pollutants in the environment, has small dimensions and a built-in silent transfer fan. The data is output to the UART interface and via the PWM signal. The set includes a UART-USB converter. Nova Fitness SDS011

Redistilled and deionized water with ultra high resistance and extremely low conductivity (below 0.1µS). MICRO CHIP ELEKTRONIC ART.036

Redistilled and deionized water with ultra high resistance and extremely low conductivity (below 0.1µS). MICRO CHIP ELEKTRONIC ART. 037

A liquid cleaner for cleaning, regenerating and caring for all kinds of rubber products with immediate action. It regenerates and refines rubber, increasing its service life many times. MICRO CHIP ELEKTRONIC ART.072

Extension module for building a 3D printer or CNC machine compatible with Arduino. The kit includes four A4988 stepper motor drivers. the module is supplied with the voltage from 12 to 36 V

2x16 character LCD display. It can display the font in any color from the RGB palette. Communication via the I2C interface. The module has a lead compliant with the Gravity standard. DFRobot DFR0554

Touch button with green LED backlight. Powered with the voltage in the range from 2.7 V to 6 V, it works with 3.3 V systems

16 Mbit, low voltage, Page-Erasable Serial Flash memory with byte alterability and a 50 MHz SPI bus interface, STM, SO8, RoHS

Miniature, 12 V brush DC motor with metal gear and 15.25:1 gear ratio. It has a cross section of 10 × 12 mm, and the D-shaped output shaft with a length of 9 mm and a diameter of 3 mm. Pololu 4788