Best sellers

Programmable wireless BT4.0 transmitter, compatible with sensors of the iNode Care Sensor series. It allows you to enable / disable other devices, eg after exceeding the set temperature or humidity, moving the sensor or changing its position. Allows you to control directly from your smartphone, tablet or computer

At the Feather M0\'s heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much). Adafruit 2796

This module enables the Feather series range to be expanded with 8 12-bit PWM outputs that can be used, for example, to control servos or LED diodes. Adafruit 2928

With a celebrated reputation as an affordable, simple and fun-to-play DIY robot kit, the Insectbot breed has now evoled to its second generation: the Insectbot Hexa. KIT0090

WiFi wireless communication module compatible with the pin spacing of XBEE modules. The module is powered by 3.3 V. The product is compatible with Arduino. DFRobot TEL0092

Module with a miniature DC motor. No additional controller is required to start the engine. The module is controlled by the PWM signal. DFRobot DFR0411

A module that allows you to create your own layout based on the Feather tile. Equipped with prototype holes and a set of screw connectors with pins out. Adafruit 2926

Pre-installed Android 4.x or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode

K type blade, bevelled knife 8mm for WEP 926 soldering station. Used for soldering in narrow places

LCD Keypad Shield V2.0 is a 2 line, 16 character Arduino LCD display expansion shield, based on V1.0. DFR0374

Evaluation kit with Bluetooth 4.0 module. It has 8 digital pins, 4 analog pins and 4 PWM. Compatible with Arduino, it is perfect as a platform for building a small robot. DFRobot DFR0351

IoT development board with ATmega32U4 microcontroller and W5500 Ethernet chip. Compatible with Arduino Leonardo, has a built-in PoE (Power over Ethernet) function. DFRobot DFR0342

Data logger dedicated to Feather plates. Equipped with RTC clock, battery slot and micro SD card slot. Adafruit 2922

Set with a measuring module and a probe for measuring electrical conductivity. It allows you to measure the salinity of water and soil. It has a Gravity analog output interface. DFRobot DFR0300

This gearmotor is a miniature medium-power, 6 V brushed DC motor with a 297.92:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. This version also has a 4.5 × 1 mm extended motor shaft.

Mounting bracket with a magnifying glass with a diameter of 85mm, with grippers, a spiral for a soldering iron, a cleaner and a sponge to clean the tip, a space for rosin and LED backlight. ZD-10Y

Soldering iron with smooth regulation of digitally controlled air discharge, with temperature regulation in the range of 100 ° C to 500 ° C

CP2102 USB to UART Module, USB micro connector

The LSM6DS33 combines a digital 3-axis accelerometer and 3-axis gyroscope into a single package. The sensor provides six independent acceleration and rotation rate readings whose sensitivities can be set in the ranges of ±2 g to ±16 g and ±125°/s to ±2000°/s, available through I²C and SPI interfaces.

Black polyurethane scooter/skate wheel 100 × 24 mm, works with standard 608 bearings. Pololu 3278