zł184.20 tax excl.
Expansion board for Raspberry Pi 5 that allows one or two M.2 NVMe SSDs in sizes from 2230 to 2280 to be connected. It uses a PCIe Gen 2 x1 interface and a PCIe switch that shares bandwidth between two M.2 M-Key slots. Version supplied without NVMe drives. Pimoroni PIM704
Expansion board NVMe Base Duo expands Raspberry Pi 5 with two M.2 M-Key slots for 2230, 2242, 2260 and 2280 NVMe SSDs. Communication with Raspberry Pi 5 is provided through the PCIe connector using the included FPC cable. Both slots operate behind a PCIe Gen 2 switch and share a single PCIe x1 connection. The manufacturer recommends PCIe Gen 2 x1 operation, providing a total throughput of approximately 450 MB/s, with over 220 MB/s per drive when both drives are accessed simultaneously.
The board can be mounted below or above Raspberry Pi 5, while compliance with the Raspberry Pi PIP design guidelines facilitates integration with the platform. The adapter can be used in file servers, media centres, home automation systems, reverse proxy servers and other projects requiring high-capacity storage or two independent NVMe drives. With up-to-date Raspberry Pi 5 firmware, booting from drives installed in NVMe Base Duo is also supported. Additional +5 V and GND pads are available on the board for supplying extra power to drives with higher power requirements.
Attention!
Manufacturer
Responsible person
NVMe Base is a reliable solution for expanding storage for the Raspberry Pi 5, ideal for users who require fast data access and large storage capacity. With support for multiple NVMe SSD models and compatibility with the Raspberry Pi 5, it is the perfect addition to projects that demand performance and flexibility. Pimoroni PIM699
PCIe 3.0 adapter with two M.2 slots designed for Raspberry Pi 5, allowing simultaneous connection of two NVMe SSDs or AI accelerators including Hailo8/8L and Google Coral. The module uses the ASM2806 PCIe switch, supports M.2 2230 / 2242 / 2260 / 2280 devices, and mounts underneath the board while keeping the GPIO header accessible for further expansion. Seeed Studio PCIe3.0 to dual M.2 hat
No product available!
HAT-type module with a PCIe interface for Raspberry Pi 5, enabling connection of an NVMe M.2 drive or a Hailo8 / Hailo8L AI accelerator. Seeed Studio 103110063
HAT+ module intended for Raspberry Pi 5 enabling power supply via Ethernet in the PoE standard and connection of an M.2 NVMe drive via the PCI Express interface. Waveshare 31536
PCIe TO 2.5G ETH Board (C) designed for Raspberry Pi 5, enabling expansion with a 2.5G Ethernet port. Supports Raspberry Pi OS, operates driver-free, and works in plug and play mode. The RTL8125 controller and PCIe interface ensure straightforward integration and high network throughput. Waveshare PCIe TO 2.5G ETH Board (C)
No product available!
Multifunctional PCIe to M.2 adapter compatible with Raspberry Pi 5, enabling connection of NVMe M.2 solid state drives and convenient breakout of HDMI ports. Supports dual 4K display outputs, offers two power supply methods, and significantly expands the functionality of Raspberry Pi 5 for desktop and embedded applications. Waveshare Pi5 Connector Adapter (C)
PCIe expansion module for Raspberry Pi 5 with four 2.5G Ethernet RJ45 ports, operating in plug and play mode without driver installation, compatible with Raspberry Pi OS. Waveshare PCIE TO 4-CH 2.5G ETH Board (B)
PCIe expansion module for Raspberry Pi 5 with four Gigabit Ethernet RJ45 ports, operating in plug and play mode without driver installation, compatible with Raspberry Pi OS. Waveshare PCIE TO 4-CH Gigabit ETH Board (B)
PCIe to M.2 NVMe and USB 3.2 Gen1 adapter designed for Raspberry Pi 5 enabling connection of an NVMe SSD while expanding the system with four USB 3.2 ports. The module supports M.2 NVMe drives in 2230, 2242, 2260 and 2280 sizes and allows booting the system directly from the SSD. The HAT+ compliant design uses the Raspberry Pi 5 PCIe interface to provide high-speed storage and additional USB connectivity. Waveshare PCIe TO M.2 USB HAT+
No product available!
HAT module for Raspberry Pi 5 with PCIe interface for M.2 NVMe drives and PCM5122 audio chip with 3.5 mm jack and RCA output. Supports 2230/2242 SSD and I2S audio without drivers. Waveshare 34170
The module enables micro:bit, Raspberry Pi Pico, RP2040-based boards, and other controllers to connect to Wi-Fi networks and online services. Communication with the host board is handled through UART, while the pre-installed ESP-AT firmware allows network functions to be controlled using AT commands. Cytron GRV-WIFI-8266
The cellular modem adds 2G, 3G, and 4G LTE connectivity to compatible Raspberry Pi computers. The HAT+ form factor, 40-pin connector, USB interface, and cellular modem functions support integration with embedded and communication systems. Teltonika EBD021
The cellular modem adds 3G, 4G, and 5G connectivity to Raspberry Pi 4 Model B and Raspberry Pi 5. The HAT+ form factor, 40-pin GPIO connector, USB data interface, and modem control signals support integration with embedded systems requiring direct cellular network access. Teltonika EBD050
The cellular modem adds 4G LTE and 5G RedCap connectivity to Raspberry Pi 4 Model B and Raspberry Pi 5. The HAT+ form factor, 40-pin connector, USB interface, and GPIO modem control support integration with embedded systems requiring direct cellular network access. Teltonika EBD070
Compact adapter designed for connecting Qwiic modules and sensors to Raspberry Pi via the I2C bus. It features 3 Qwiic connectors, a female header matching the Raspberry Pi pinout, and additional 3.3 V, 5 V, and GND pins. Soldered 333019
CAN communication module with an MCP2518FD controller and ATA6563 transceiver, designed for connecting microcontrollers to CAN buses used in automotive, automation, and industrial systems. It supports CAN 2.0B and CAN FD, an SPI interface, data rates up to 8 Mbps, and a 120 Ω termination resistor enabled via a jumper. Soldered 333020
No product available!
Expansion board for Raspberry Pi 5 that allows one or two M.2 NVMe SSDs in sizes from 2230 to 2280 to be connected. It uses a PCIe Gen 2 x1 interface and a PCIe switch that shares bandwidth between two M.2 M-Key slots. Version supplied without NVMe drives. Pimoroni PIM704
Expansion board for Raspberry Pi 5 that allows one or two M.2 NVMe SSDs in sizes from 2230 to 2280 to be connected. It uses a PCIe Gen 2 x1 interface and a PCIe switch that shares bandwidth between two M.2 M-Key slots. Version supplied without NVMe drives. Pimoroni PIM704