Main view
search
  • Main view
  • Product with packaging
  • Top view
  • Bottom angled view
  • Full kit
ID: 1201759
5902186337589
zł216.50
Tax included

zł176.02 tax excl.

PCIe 3.0 adapter with two M.2 slots designed for Raspberry Pi 5, allowing simultaneous connection of two NVMe SSDs or AI accelerators including Hailo8/8L and Google Coral. The module uses the ASM2806 PCIe switch, supports M.2 2230 / 2242 / 2260 / 2280 devices, and mounts underneath the board while keeping the GPIO header accessible for further expansion. Seeed Studio PCIe3.0 to dual M.2 hat

24h
Available
Available quantity: 2
Kamami is the official distributor of Seeed Studio modules and development kits. All products of this brand in our offer are original and come directly from the manufacturer.

Description

Seeed Studio PCIe3.0 Switch to Dual M.2 HAT for Raspberry Pi 5 expands Raspberry Pi 5 with two independent M.2 slots operating over the PCIe 3.0 interface. The module features the ASMedia ASM2806 PCIe switch, allowing a single PCIe lane from Raspberry Pi 5 to be split into two high-bandwidth endpoint devices. The solution supports connecting two NVMe SSDs for increased storage capacity, RAID configurations, SSD boot operation, or simultaneous use of storage and an AI accelerator.

                                                                         p1201759-PCIE2.0-3.0%20COMPARISION.png

The board supports NVMe M.2 devices in 2230, 2242, 2260, and 2280 form factors, as well as Hailo8, Hailo8L, and Google Coral TPU accelerators using the M.2 interface. The manufacturer confirms full support for dual NVMe SSD operation and NVMe + AI configurations. Hailo8L compatibility is available exclusively for modules in the M.2 Key B+M version. The adapter mounts underneath Raspberry Pi 5 and connects using an FPC cable, leaving the 40-pin GPIO header available for simultaneous use with additional HATs or expansion modules. Additional Pogo Pin contacts provide increased power delivery required for stable operation of two M.2 devices under high data transfer loads.

Notes

  • Not all NVMe M.2 SSDs are fully compatible with Raspberry Pi 5
  • Firmware and bootloader update is recommended when booting the system from SSD
  • SATA M.2 drives are not supported
  • Official Raspberry Pi Foundation enclosure is not compatible with the HAT - the manufacturer provides a dedicated 3D-printable enclosure model
  • S-shaped FPC cable does not block access to the microSD card slot

Features

  • Device type: PCIe 3.0 to 2 × M.2 adapter for Raspberry Pi 5
  • Base compatibility: Raspberry Pi 5
  • PCIe switch chipset: ASMedia ASM2806
  • Number of M.2 slots: 2
  • Supported M.2 interfaces: NVMe PCIe, M.2 AI accelerators
  • Supported M.2 sizes: 2230, 2242, 2260, 2280
  • Maximum bus speed: PCIe Gen 3.0
  • Maximum power input: 5 V / 3 A
  • Additional power delivery: Pogo Pin 2 A + PCIe connector 1 A
  • Raspberry Pi connection type: FPC cable
  • Mounting method: rear / underside mounting for Raspberry Pi 5
  • 40-pin GPIO header remains accessible after installation
  • Compatible with Google Coral TPU
  • Compatible with Hailo8 / Hailo8L (Hailo8L requires M.2 Key B+M version)
  • Supports dual NVMe SSDs
  • SSD boot support*
  • SATA M.2 drives not supported
  • Manufacturer-provided 3D-printable enclosure model

Kit includes

  • PCIe 3.0 to 2 × M.2 adapter
  • 2 × 50 mm FPC cables
  • Mounting screws and standoffs set
1201759

Data sheet

Compatible with
Raspberry Pi 5

Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20

Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20

Other products in the same category (16)