ACS724 Current Sensor Carrier - module with ACS724 ±20A current sensor
ID: 586600
5906623480487
zł44.72
Tax included
zł36.36 tax excl.
Module with ACS724 current sensor with a measuring range of direct and alternating current from 0 to 10 A. It communicates via an analog interface. Pololu 4045
Description
Module with a two-way Hall current sensor based on the ACS724LLCTR-20AB system. It allows you to measure the current in the range from -20 to 20 A. The board is powered with the voltage from 4.5 V to 5.5 V and is intended for use in circuits with a logical voltage of 5 V. It offers a current path with low resistance (~ 1.2 mΩ) and electrical insulation up to 2.4 kV RMS. The output is a proportional analog voltage (100 mV/A) centered at 2.5 V with an error of ± 0.8%.
The sensor requires five connections to work properly: input current (IP+ and IP-), logic power (VCC and GND) and sensor output (OUT). Pin FILTER allows you to adjust the bandwidth of the plate by adding a capacitor to ground in parallel with the 1 nF capacitor that is already on the board. Without an additional external filter capacitor, the frequency response is approximately 90 kHz.
Features
- Hall effect differential detection
- Internal resistance of 1.2 mΩ conducting path
- Electrical insulation up to 2.4 kV RMS
- 120kHz high bandwidth for fast response times
- Ability to filter the output data to improve the resolution
- Integrated digital temperature compensation circuit
- Operating voltage 4.5 to 5.5 V
- Current measuring range from -20 to 20 A
- Output resolution 0.1 V/A
- Working temperature range from -40°C to 150°C
- Dimensions: 17.8 x 20.3 mm
- Weight: 1.1 g
Kit contains
- ACS724 Current Sensor Carrier module
- Straight 3-pin male connector
586600
Data sheet
- Interface
- Sygnał analogowy
- Zakres pomiarowy
- ±20 A
- Sposób podłączenia
- Szeregowy
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 20 A. DFRobot SEN0211
zł92.27
24h
Available quantity: 2
Available
Module with ACS724LLCTR-30AU current sensor with a measuring range of direct and alternating current from 0 to 30 A. It communicates via an analog interface. Pololu 4046
zł40.55
24h
Available quantity: 3
Available
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 5A. DFRobot SEN0287
zł81.82
24h
Available quantity: 3
Available
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
zł4.35
24h
Available quantity: 203
Available
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
zł4.31
Delivery date unknown
No product available!
A set of 40 pcs of male-male connecting cables in various colors, 10 cm long
zł5.49
24h
Available quantity: 14
Available
Other products in the same category (16)
A compact Hall-effect current sensor that provides accurate DC and AC current measurement within a ±10 A range with galvanic isolation. It features a high-sensitivity analog VOUT output with a 150 kHz bandwidth, enabling fast and precise readings in dynamic systems. The module operates over a wide temperature range of -40°C to 125°C, and the low current path resistance minimizes energy loss. Its small size and flexible mounting options make it ideal for prototyping, industrial systems, and space-constrained projects. Pololu 5444
zł16.91
24h
Available quantity: 3
Available
No product available!
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5255
zł52.68
24h
Available quantity: 2
Available
The ACS71240 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 120 kHz) and low conduction resistance (0.6 mΩ), it minimizes energy loss and offers a fast response time of less than 5 µs. Pololu 5244
zł22.15
24h
Available quantity: 3
Available
A modern current sensor combining the Hall effect with an inductive coil, which allows for precise measurements of both the DC and AC components up to 5 MHz. Thanks to its lightning-fast response time and low path resistance, it is perfect for motor control systems, power converters and protection systems. Pololu 5235
zł63.04
24h
Available quantity: 2
Available
The ACS71240 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 120 kHz) and low conduction resistance (0.6 mΩ), it minimizes energy loss and offers a fast response time of less than 5 µs. Pololu 5245
zł21.37
24h
Available quantity: 3
Available
A compact Hall-effect current sensor that provides accurate DC and AC current measurement within a ±30 A range with galvanic isolation. It features an analog VOUT output with a sensitivity of 44 mV/A and a 150 kHz bandwidth, enabling fast and precise readings in dynamic systems. The module operates over a wide temperature range of -40°C to 125°C, and the low current path resistance (~1.6 mΩ) minimizes energy loss. Its small size and flexible mounting options make it ideal for prototyping, industrial systems, and space-constrained projects. Pololu 5441
zł15.89
24h
Available quantity: 3
Available
The current measurement with a value of 0 - 5A is realized by the ACS712-05 system based on the Hall effect. The system sensitivity is 185mV / A (analog signal).
zł8.95
24h
Available quantity: 2
Available
Precision Hall effect current sensor offering galvanic isolation, wide bandwidth of 150 kHz and the ability to measure AC and DC current with very low power loss. Thanks to differential measurement and immunity to magnetic interference, it is perfect for applications requiring accurate current monitoring, such as power supplies, converters or motor control systems. Pololu 5293
zł29.32
24h
Available quantity: 5
Available
The ACS71240 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 120 kHz) and low conduction resistance (0.6 mΩ), it minimizes energy loss and offers a fast response time of less than 5 µs. Pololu 5246
zł21.37
24h
Available quantity: 3
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5270
zł71.45
24h
Available quantity: 2
Available
Voltage and current sensor module. It works with a shunt resistor and voltage divider and the INA-169 chip and can measure voltages up to 52 V and currents up to 90 A. SparkFun SEN-16408
zł136.90
3 weeks
No product available!
This board is a simple carrier of Broadcom’s bidirectional ±50A ACHS-7125 Hall effect-based linear current sensor, which offers a low-resistance (~0.7 mΩ) current path and electrical isolation up to 3 kV RMS. Pololu 4034
zł17.72
24h
Available quantity: 3
Available
No product available!
Compact current sensor based on TMR technology, enabling precise measurements up to 30 A with minimal energy losses. Thanks to a wide 1 MHz bandwidth, galvanic isolation and interference immunity, it is perfect for applications requiring fast response and high accuracy. Pololu 5317
zł52.79
24h
Available quantity: 2
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5252
zł56.70
4 weeks
No product available!
Module with ACS724 current sensor with a measuring range of direct and alternating current from 0 to 10 A. It communicates via an analog interface. Pololu 4045