zł101.42 tax excl.
A module with a distance and gesture sensor that allows the detection of objects in two axes (x and z) and the detection of simple gestures. It communicates via the I2C or UART interface. SparkFun SEN-13162
A module with a distance and gesture sensor that allows the detection of objects in two axes and the detection of simple gestures. Developed in collaboration with XYZ Interactive, the sensor uses GestureSense® technology to recognize an object-to-sensor distance of up to approximately 30 cm (referred to as the "Z" axis) and locate an object on the side of the sensor over a span of approximately 15 cm, known as the "X" axis. The module performs the measurement by emitting infrared (IR) light beams through two LEDs on both sides of the object, detection by the receiver in the middle of the sensor and data interpretation by the built-in microcontroller. The user can use the I2C or UART interface for communication. Full documentation with examples of use is available on the product page.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Pin header goldpin black 1x40 pins. Straight connector for through-hole assembly. 2.54mm pitch.
This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 5V Arduino boards. It can also be used for general serial applications. DEV-09716
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
No product available!
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
The GP2Y0A60SZ offers a wide detection range of 4″ to 60″ (10cm to 150cm) and a high update rate of 60Hz. The distance is indicated by analog voltage - only a single analog input is required to interface with the module. Pololu 2476
Suitable for outdoor applications such as car reversing sensors, security alarms, industrial inspection, etc. SEN0207
This sensor is a carrier/breakout board for ST’s VL53L0X laser-ranging sensor, which measures the range to a target object up to 2 m away.
This module features a fixed-gain, 38 kHz modulated IR sensor and a corresponding IR LED with oscillator circuit to make a tiny proximity sensor.
This module features a fixed-gain, 38 kHz modulated IR sensor and a corresponding IR LED with oscillator circuit to make a tiny proximity sensor. This low-brightness version draws an average of 8 mA at 5 V and has a typical sensing range up to approximately 12 inches (30 cm).
Adafruit VL53L0X Time of Flight Distance Sensor is a laser distance sensor using the ToF (Time of Flight) measurement technique. The module is powered by 2.8 ... 5V voltage and can measure up to 1000mm. Adafruit 3317
ToF distance sensor module based on the VL6180X system. It offers a range of up to 10 cm and communicates via the I2C interface. Adafruit 3316
No product available!
Laser rangefinder with measuring range up to 22m. The current consumption is up to 200mA and the supply voltage 4.5 ... 6V. Communication via UART or CAN interface. DFRobot SEN0238
A multifunctional module with an optical sensor for measuring the intensity of illumination, the color of the incident RGB light, the distance from the object and the detection of 3D gestures. Adafruit 3595
VL53L0X ToF Laser Range Finder is a laser distance sensor using the ToF (Time of Flight) measurement technique. The module is supplied with 3.3 ... 5 V voltage and can measure up to 2 m. DFRobot SEN0245
No product available!
Range finder with a measuring range up to 12m. The current consumption is up to 120mA and the supply voltage 4.5 ... 6V. Communication via the UART interface. DFRobot SEN0259
Distance sensor module operating in TOF technology, operating range 4-400 cm, resolution up to 1 mm. Communication with the sensor via the I2C bus. Power supply through a built-in regulator with voltage from 2.6 to 5.5 V. Pololu 3415
A module with a distance and gesture sensor that allows the detection of objects in two axes (x and z) and the detection of simple gestures. It communicates via the I2C or UART interface. SparkFun SEN-13162