TLC5940 Breakout (BOB-10616)
Description:
The TLC5940 is a 16 channel PWM unit with 12 bit duty cycle control (0-4095), 6 bit current limit control (0-63), and a daisy chainable serial interface. This breakout board is a good way to take full advantage of this useful IC. All 16 PWM channels are broken out to standard 0.1" headers, which run alongside convenient voltage and ground rails. Also, because the TLC5940 can be daisy-chained, the breakout is designed to support that feature. On the left-hand side of the board all serial inputs are broken out to 0.1" headers and likewise with output on the right-hand side.
Use this board to increase the number of PWM pins available to your microcontroller for applications such as Monocolor, Multicolor or Full-Color LED Displays, LED Signboards, Display Backlighting, Servo control, or any other project where a large number of PWM drivers are necessary.
Note: While each 3-pin PWM header is 0.1" spaced, the space between each header is slightly larger in order to accommodate servo connections. In order to make this board suitable for use with servos, 2.2k pull-up resistors have been included on each output as well. Finally, the 2.2k resistor on the Iref pin sets the output current to 17.8mA but a parallel through-hole connection is provided for an additional resistor to increase the current if necessary. To determine the resistor value you need for a given output check the equations provided on the schematic.
Documents:
Manufacturer
Responsible person
FRAM chip has 64 Kbits (8 KBytes) of storage, interfaces using SPI, and can run at up to 20MHz SPI clock rates. Each byte can be read and written instantaneously (like SRAM) but will keep the memory for 95 years at room temperature. Adafruit 1897
Motion Processing Unit, 3-Axis Gyro + 3-Axis Accel MEMS Device, I2C, QFN24, InvenSense, RoHS
Adafruit 2094 - JTAG (2x10 2.54mm) to SWD (2x5 1.27mm) Cable Adapter Board
LED matrix display module (in red color) with an organization of 14 columns x 9 lines, compatible with Arduino.
Prototype contact plate 170 points, 35x47 mm in red color. PPS0170 RED
No product available!
Digital controller for wireless battery charger (WBC) transmitters Qi 1.1.2 A11 certified, PMA compatible, VFQFPN32, STM, RoHS
32-bit microcontroller from the STM32F0 family with ARM Cortex-M0 core, 32kB Flash memory, 16kB RAM, 48MHz, I2C, SPI, UART / USART, USB, DMA, POR, PWM, WDT, 2.4 ... 3.6 V, A / D 13x12b, 20-TSSOP
No product available!
32-bit microcontroller from the STM32F4 family with ARM Cortex-M4 core, 1MB Flash memory, 256kB SRAM memory, 180MHz, I2C, ISPI, UART / USART, USB OTG, 1.8 ... 3.6V, 208LQFP, STM, RoHS
32-bit microcontroller from the STM32F3 family with ARM Cortex-M4 core, 512kB Flash memory, 80kB SRAM, I2C, SPI, UART / USART memory, CAN, 1.8 ... 3.6V, 100LQFP, STMicroelectronics, RoHS
32-bit microcontroller from the STM32L4 family with ARM Cortex-M4 core, 512kB Flash memory, 128kB SRAM, I2C, SPI, UART / USART memory, USB, CAN, 1.71 ... 3.6V, 100LQFP, STM, RoHS
32-bit microcontroller from the STM32L4 family with ARM Cortex-M4 core, 1MB Flash memory, 128kB SRAM, I2C, SPI, UART / USART memory, USB, CAN, 1.71 ... 3.6V, 100LQFP, STM, RoHS
32-bit microcontroller from the STM32L4 family with ARM Cortex-M4 core, 512kB Flash memory, 128kB SRAM, I2C, SPI, UART / USART memory, USB, CAN, 1.71 ... 3.6V, 144LQFP, STM, RoHS
Controller for STMicroelectronics inverters in flyback and buck-boost topology designed for LED control. The system also allows the implementation of buck, boost and SEPIC topologies. Has a SSOP10 housing
Miniature (25x40mm) WiFi b/g/n module for surface mounting with support for TCP and UDP protocols operating in standalone and access point modes. The module is equipped with UART and Ethernet interfaces, it is also possible to control GPIO lines. Powered by 3.3V
No product available!
Prototype contact plate 170 points 35x47 mm in black color. PPS0170 BLACK
TLC5940 Breakout