Gravity: I2C RGB LED Colorful Button - button module with RGB backlighting
ID: 1182942
5902186310810
zł53.64
Tax included
zł43.61 tax excl.
A push-button module with RGB LED backlighting. The board is equipped with a Gravity connector and communicates via an I2C interface. DFRobot DFR0991
Description
A push-button module with RGB LED backlighting. It communicates via the I2C interface (Gravity connector) and is powered by 3.3 V or 5 V. It has a built-in DIP switch for setting I2C addresses, so you can cascade up to 8 such modules to a single bus. Full documentation of the module with examples of use is available on the product page.
Features
- RGB LED
- I2C interface
- Address: 0x23 to 0x2A
- I2C address configuration using DIP switches
- Interrupt mode: signal high when button is pressed
- Number of button cycles: 200 000
- Gravity connector
- Power supply voltage: 3.3 V or 5 V
- Dimensions: 37 x 32 x 19.5 mm
Kit contains
- Gravity Module: I2C RGB LED Colorful Button
- Gravity I2C/UART 4-pin cable
1182942
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
No product available!
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
zł21.92
24h
Available quantity: 4
Available
A set of 10 cables, 30 cm long, compliant with the Gravity standard. DFRobot FIT0513
zł27.58
24h
Available quantity: 3
Available
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
zł4.31
24h
Available quantity: 404
Available
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
zł4.31
24h
Available quantity: 117
Available
Other products in the same category (16)
I2C BME680 Environmental Sensor is a gas, pressure, temperature and humidity sensor in one MEMS housing. The module is supplied with 3.3-5V, for communication the I2C or SPI interface is used. DFRobot SEN0248
zł112.72
24h
Available quantity: 2
Available
Gravity: Digital Peristaltic Pump is a peristaltic pump with a controller and a connector compatible with modeling servos. The set is powered by 5 ... 6 V. DFRobot DFR0523
zł111.23
24h
Available quantity: 3
Available
DFRobot Gravity analog light intensity module for Arduino and Raspberry Pi. DFRobot DFR0026
zł11.01
24h
Available quantity: 2
Available
Module with a button, LED diode and a blue cap. DFRobot DFR0029-B
zł7.55
4 weeks
No product available!
Digital orientation sensor module. DFRobot DFR0028
zł7.52
24h
Available quantity: 2
Available
Module with 5 A 250 VAC relay. DFRobot DFR0017
zł12.63
24h
Available quantity: 3
Available
Fan module with DC motor, propeller and connection cable. DFRobot DFR0332
zł29.22
24h
Available quantity: 3
Available
LM35 analog temperature sensor module for Arduino. DFRobot DFR0023
zł15.88
24h
Available quantity: 1
Available
PIR motion sensor module for Arduino and Raspberry Pi. DFRobot SEN0018
zł19.46
24h
Available quantity: 6
Available
Micro:Mate is an expansion board for the micro: bit development module. It provides six 3-pin connectors with I/O outputs, a 3.5mm audio jack connector and is powered from a 5V microUSB connector. DFRobot DFR0518
zł30.90
4 weeks
No product available!
VL53L0X ToF Laser Range Finder is a laser distance sensor using the ToF (Time of Flight) measurement technique. The module is supplied with 3.3 ... 5 V voltage and can measure up to 2 m. DFRobot SEN0245
zł65.19
4 weeks
No product available!
2x1.2A DC Motor Driver is a dual controller of DC motors with a Gravity connector, supplied with 2.5 ... 12V voltage with a maximum current consumption of 1.2A (3.2A peak) per channel. DFRobot DRI0044-A
zł40.02
4 weeks
No product available!
Gravity: DS18B20 Temperature Sensor is a module with a temperature sensor compatible with Arduino boards. The module can be supplied with 3.3-5V voltage and measures the temperature in the range -55 ~ 125 ° C. DFRobot DFR0024
zł25.04
24h
Available quantity: 1
Available
Gravity: Joystick Module V2 is a joystick module with two analog outputs (X and Y axis) and a digital output (Z axis) supplied with 3.3 ... 5V voltage. DFRobot DFR0061
zł23.70
24h
Available quantity: 1
Available
Gravity: Digital IR Receiver Module is a module with an IR receiver operating at 38kHz. The module is supplied with 5V voltage. DFRobot DFR0094
zł20.97
24h
Available quantity: 1
Available
Gravity: Vibration Motor Module is a module with a small vibration motor powered by 5V voltage, controlled by a binary signal (high / low state) or using a PWM signal. DFRobot DFR0440
zł10.97
24h
Available quantity: 2
Available
A push-button module with RGB LED backlighting. The board is equipped with a Gravity connector and communicates via an I2C interface. DFRobot DFR0991