The flame detector module detects the source emitting a wavelength between 760 and 1100 nm. It allows to detect, among others source of fire. The sensor probe has a detection angle of 60 °. When working with the sensor, make sure that the flame is not too close to the sensor, as it may damage it. The sensor has an analog output. The module is equipped with a Gravity connector and supports the Arduino series of boards.
An example of use is available on the product Wiki page.
Manufacturer
Responsible person
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
VL53L0X ToF Laser Range Finder is a laser distance sensor using the ToF (Time of Flight) measurement technique. The module is supplied with 3.3 ... 5 V voltage and can measure up to 2 m. DFRobot SEN0245
No product available!
2x1.2A DC Motor Driver is a dual controller of DC motors with a Gravity connector, supplied with 2.5 ... 12V voltage with a maximum current consumption of 1.2A (3.2A peak) per channel. DFRobot DRI0044-A
Gravity: DS18B20 Temperature Sensor is a module with a temperature sensor compatible with Arduino boards. The module can be supplied with 3.3-5V voltage and measures the temperature in the range -55 ~ 125 ° C. DFRobot DFR0024
Gravity: Joystick Module V2 is a joystick module with two analog outputs (X and Y axis) and a digital output (Z axis) supplied with 3.3 ... 5V voltage. DFRobot DFR0061
Gravity: Digital IR Receiver Module is a module with an IR receiver operating at 38kHz. The module is supplied with 5V voltage. DFRobot DFR0094
No product available!
Gravity: Vibration Motor Module is a module with a small vibration motor powered by 5V voltage, controlled by a binary signal (high / low state) or using a PWM signal. DFRobot DFR0440
Gravity: Digital Capacitive Touch Sensor is a capacitive touch sensor powered by 3.3V ... 5V voltage. DFRobot DFR0030
Gravity: Digital Crash sensor is a microswitch module (left) often called a limit switch. The module is powered by 5V voltage and has a digital two-state output. DFRobot SEN0138-L
Gravity: Digital Crash sensor is a microswitch module (right) often called a limit switch. The module is powered by 5V voltage and has a digital two-state output. DFRobot SEN0138-R
Module with an IR transmitter operating at a frequency of 38kHz. The module is supplied with the voltage from 3 to 5V. FRobot DFR0095
Gravity sensor adapter with 3-pin terminal connector. There are two 10 kΩ pull-up and pull down resistors on the board, set with a jumper. DFRobot DFR0055
Module with blue LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0021-B
Module with red LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0021-R
Module with white LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0021-W
Gravity: I2C 12-Bit DAC is a module with 12-bit DAC and built-in EEPROM memory. The module is powered by 3.3 ... 5V for communication used by the I2C interface. DFRobot DFR0552
Gravity: I2C ADS1115 The 16-Bit ADC Module is an analogue-to-digital converter module for Arduino and Raspberry Pi. This module uses 16-bit ADC ADS1115 and is powered by 3.3 ... 5V. DFRobot DFR0553
he flame detector module detects the source emitting a wavelength between 760 and 1100 nm. It allows to detect, among others source of fire. Analog interface. DFRobot DFR0076