Grove Thermal Imaging Camera - module with MLX90641
ID: 583068
5906623415182
zł547.69
Tax included
zł445.28 tax excl.
Module with a MLX90641 thermal imaging camera with a 16x12 field matrix and a 110° viewing angle. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020892
Description
Module with a MLX90641 thermal imaging camera with a 16x12 field matrix and a 110° viewing angle. It enables temperature measurement in the range from -40°C to 300°C with high accuracy down to 1°C. The infrared thermal imager is equipped with a sensitive heat sensor that can detect slight differences in the temperature of objects in the environment. It then collects this radiation information from the objects and creates an electronic image based on the temperature difference information. The board is equipped with a Grove connector, so it can be used with the Base Shield V2. The module communicates via the I2C interface and is supplied with the voltage of 3.3 V or 5 V. Full documentation of the module with examples of use is available on the product page.
Attention!
To operate the module, a chip with at least 20 KB of RAM is required.Features
- Sensor: MLX90641
- Resolution: 16x12
- FoV: 110° x 75 °
- Temperature measurement range: -40 ? to 300 ?
- Refresh rate: 0.5Hz to 64Hz
- I2C interface
- Supply voltage: 3.3 V or 5 V
- Current consumption: 18 mA
583068
Data sheet
- Resolution
- 16 x 12
- Interface
- I2C
- Sensor
- MLX90641
- IR filter
- No
- Lens assembly
- none
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
A small module, matching the breadboard, containing a 32-bit microcontroller with ARM Cortex M7 core. PJRC TEENSY40
zł128.39
24h
Available quantity: 21
Available
Module with a MLX90641 thermal imaging camera with a 16x12 field matrix and a 110° viewing angle. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020892
zł547.69
24h
Available quantity: 1
Available
Other products in the same category (16)
Module with slot optical sensor TCUT1600X01. The board is equipped with a Grove connector and has two digital outputs. Seeed Studio 101020587
zł56.30
24h
Available quantity: 2
Available
A set of necessary tools needed to perform vehicle diagnostics. It consists of a CAN Bus module, an OBD II connector and the necessary wires. Seeed Studio 114991438
zł104.00
24h
Available quantity: 1
Available
Module with liquid turbidity sensor. The board is equipped with a Grove connector and communicates via a digital or analog interface. Seeed Studio 101020752
zł133.75
24h
Available quantity: 3
Available
Module with LoRa transmitter based on RFM95 (SX1276 LoRa®). It works with a frequency of 433 MHz, maximum power up to 100 mW and a power gain of up to + 20dBm. The module has a built-in antenna, but it is possible to connect an external antenna (MHF connector). The module has a connector in accordance with the Grove standard. Seeed studio 113060007
zł84.92
24h
Available quantity: 1
Available
Module for recording sounds, which can store recordings up to 20 seconds. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 107020007
zł37.82
24h
Available quantity: 1
Available
Module allowing collision / vibration detection (based on the MVS0608.02 system). Permitted to detect collisions irrespective of direction, provides high stability and is highly sensitive. The module has a connector in accordance with the Grove standard. Seeed studio 101020005
zł50.49
24h
Available quantity: 2
Available
Module with ITR9909 proximity sensor that can detect the presence of objects in the range from 9 to 30 cm. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020175
zł37.04
24h
Available quantity: 2
Available
A 4-core cable with a length of 30 cm, both terminated with a Grove plug. Seeed Studio 110990040
zł10.74
4 weeks
No product available!
Module with 4-digit 7-segment display with red digits. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 111020044
zł33.37
24h
Available quantity: 2
Available
The module with the tilt sensor, the sensor output is a digital signal. The module has a connector in accordance with the Grove standard. Seeed studio 101020025
zł17.37
24h
Available quantity: 2
Available
Module with 8x8 LED matrix in red and HT16K33 LED driver. The board is equipped with a Grove connector and communicates via I2C. Seeed Studio 104020089
zł69.62
4 weeks
No product available!
Module with FM receiver, with its help it is possible to receive radio waves broadcast in the FM band (frequency 50-115MHz). The module has been equipped with a 3,5mm jack socket, through which you can connect headphones. The module has a connector in accordance with the Grove standard. Seeed Studio 107020006
zł63.39
4 weeks
No product available!
Module with a 16-channel PWM PCA9685 driver. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 108020102
zł71.07
24h
Available quantity: 1
Available
Module with LCD display 16x2 characters with RGB backlight. The board is equipped with a Grove connector and communicates via I2C. Seeed Studio 104030001
zł99.68
24h
Available quantity: 2
Available
The Hall sensor module allows magnetic field detection, can be used to measure angle of rotation, displacement, mechanical vibrations, etc. The module has a connector in accordance with the Grove standard. Seeed studio 101020046
zł13.76
4 weeks
No product available!
MH-Z16 carbon dioxide sensor with Grove connector. It communicates via the UART interface. Seeed Studio 101020067
zł563.83
24h
Available quantity: 1
Available
Module with a MLX90641 thermal imaging camera with a 16x12 field matrix and a 110° viewing angle. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020892