KAmodPCAL6408 - 8-channel I2C expander module
ID: 586091
5906623432837
zł16.90
Tax included
zł13.74 tax excl.
The KAmodPCAL6408 is an 8-bit I/O expander with the PCAL6408A chip by NXP, controlled by the I2C interface.
Description
KAmodPCAL6408 is an 8-bit I/O expander with I2C control. It has 8 GPIO outputs/inputs. The module has the ability to select the address of the system, so that 2 such modules can be connected to one bus. The board is equipped with a standard Pmod I2C connector and a KAMAMI connector, allowing for easy connection of the module to the development kits. Thanks to its small dimensions, the product can be used in many development projects, while the Pmod straight-through connector allows you to connect boards in rows.
Properties
- NXP PCAL6408A chip
- 8 programmable inputs / outputs
- I2C bus
- Programmable interrupt output
- Ability to select chip address (0x20 or 0x21)
- Pass-through connector compatible with Pmod standard, allows for serial connection of Pmod I2C modules
- Connector compatible with KAMAMI standard
- Built-in pull-up jumpers on I2C bus lines
- Built-in jumper for connecting INT line of system to INT line of Pmod connectors
- Built-in I2C address selector
- Possibility to power supply with voltage in the range 1.7-5.5 V through the Pmod connector and 1.8-5.5 V through the KAMAMI connector
- Mounting holes 2.5mm in diameter
- Dimensions: 61.2 x 20.3 x 10mm
586091
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
A 30 cm long connecting cable (4 wires) designed for use with Kamami KAmod modules. It is terminated on both ends with a plug that fits the WF04S connector that KAmod modules are equipped with. cabhu04-30
zł6.90
24h
Available quantity: 3
Available
Other products in the same category (16)
KAmodL3GD20 is a digital gyroscope module with L3GD20 chip. It makes possible to measure angular velocity up to ± 2000 degrees per second. It has a embedded voltage regulator and level translators on SDA/SCL lines, thanks to which it can be used in systems supplied with a voltage of 2.5 V-5.5 V. KAmodL3GD20
zł39.90
24h
Available quantity: 100
Available
KAmodMMA8653FC is a module with NXP's MMA8653FC three-axis accelerometer. The sensor allows the measurement of acceleration in the range of ± 2g / ± 4g / ± 8g, the measurement frequency is from 1.56 Hz to 800 Hz. Communication with the sensor takes place via the I2C interface
zł26.90
24h
Available quantity: 459
Available
KAmodHTS221 is a module that allows the measurement of humidity and temperature, and thanks to the built-in stabilizer and translator levels, it can be successfully used in systems supplied with a voltage of 2.5 - 5.5 V
zł34.90
24h
Available quantity: 218
Available
Available
KAmodBT-HC05 is a Bluetooth module configured via AT commands. It has integrated LEDs indicating operating mode and connection status with the paired device, as well as a logic level translator on UART lines. KAmodBT-HC05
zł49.90
24h
Available quantity: 74
Available
Module with DS18B20 temperature sensor from Dallas Semiconductor. The sensor used allows you to measure temperatures in the range -55 ~ 125 ° C with an accuracy of ± 0.5 ° C (in the range of -10 ~ 85 ° C). The 1-Wire interface is used for communication. The plate is equipped with a goldpin connector and a KAMAMI connector, allowing easy connection of the module to the commissioning kits.
zł13.90
24h
Available quantity: 370
Available
ZL5USB is a USB-UART converter module based on Silabs CP2102. The module has small sizes, microUSB connector and it can works with the 2.5...5.5V signals.
zł24.90
24h
Available quantity: 318
Available
Available
KAmodLSM6DS3 is a module that allows measurement of acceleration and angular velocity values. It has a built-in voltage stabilizer and level translators on SDA / SCL lines, thanks to which it can be used in 2.5-5.5V voltage systems
zł27.48
24h
Available quantity: 119
Available
zł5.90
24h
Available quantity: 480
Available
Available
KAmodMC3635 is a module with the MC3635 three-axis accelerometer from mCube. The sensor allows the measurement of acceleration in the range of ±2g/±4g/±8g/±12g/±16g, the measurement frequency is from 14 to 1300 Hz. Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMC3635
zł14.90
24h
Available quantity: 453
Available
Pressure sensor module with I2C interface (MPL115A2)
zł44.90
24h
Available quantity: 19
Available
KAmodLSM303C is a module with the MEMS LSM303C chip from STMicroelectronics. The chip has a digital signal output (I2C or SPI bus) and allows measurement of accelerations and magnetic field values in three axes
zł37.90
24h
Available quantity: 406
Available
Available
Available
The KAmodPCAL6408 is an 8-bit I/O expander with the PCAL6408A chip by NXP, controlled by the I2C interface.