FGSensors FG-3+ Sensor-1-axle magnetic field sensor

Module with TLV493D 3-axis magnetic field sensor. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4366

Module with a 3-axis magnetometer based on the BMM150 system. It communicates via the I2C or SPI interface. DFRobot SEN0419

Module with a 3-axis MMC5983MA mega-meter. Equipped with a Qwiic connector, it communicates via the I2C interface. SparkFun SEN-19921

Module with a 3-axis magnetic field sensor MMC5603. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5579

A module with a 3-axis magnetometer based on the BMM150 chip. It communicates via an I2C interface. DFRobot SEN0529

Module with a 3-axis magnetometer based on the BMM150 chip. It communicates via an I2C or SPI interface. Waveshare BMM150 3-Axis Magnetometer Sensor

Advanced electronic compass module that precisely calculates direction to within a few degrees, and its tilt compensation allows operation in difficult environmental conditions. The module is easy to use and allows to obtain measurement data via I2C interface at 5 Hz. SparkFun SEN-12916

A sensitive sensor of the magnetic field, operating in the range of ± 50 microtesels, which generates a rectangular signal proportional to the strength of the field, which facilitates its integration with microcontrollers. It is distinguished by high temperature stability and tenderness, which makes it ideal for precise magnetic field measurements in applications requiring reliability. Sparkfun Sen-25531

The GY‑271 module with HMC5883L sensor is a precise digital compass offering three-axis magnetic field measurement, I²C communication, and 3 V–5 V operation. Suitable for robotics, navigation, and embedded systems requiring low power consumption and a compact form factor. GY‑271

Complete kit for building a gradiometer, including two FG-3+ magnetometer sensors, a PCB board, Android-enabled software, and a mobile app. The kit allows for easy assembly and quick start-up of the device, which will immediately start displaying readings on the LCD after connection. Additional accessories, such as sensor holders, sensor tuning pipes, and a housing, provide convenience, safety, and precise adjustment of the device to use. SparkFun WIG-25530

Precise, 3-axis geomagnetic sensor based on FlipCore and TMR technology, offering high interference immunity and a wide measurement range of ±2000μT with a resolution of 0.1μT. Thanks to its high sampling rate (up to 400Hz) and resistance to magnetic shocks, it is ideal for AR/VR systems, AGV navigation and drone control. DFRobot SEN0622

Precise 3-axis compass based on FlipCore and TMR technology, offering magnetic field measurement in the range of ±2000μT without the need for calibration. With I3C support, sampling rate up to 400 Hz and Field Shock Recovery function, it is perfect for navigation systems, AR/VR, drones and autonomous vehicles. DFRobot SEN0619

Precise Hall effect sensor that converts magnetic field intensity into analog voltage. Differential response to magnetic poles (voltage increases when approaching S pole and decreases at N pole) enables precise analysis of field direction and strength. High sensitivity, low noise and compatibility with platforms such as Arduino and micro:bit make the sensor ideal for industrial, educational and hobby applications. DFRobot DFR1132

Rotary angle sensor module based on the AS5600, enabling contactless magnetic position measurement over a 0–360° range, featuring an I2C interface and STEMMA QT / Qwiic connectors for solderless connection. Adafruit 6357

The Zeenko near-field probe set based on a 4-layer PCB enables precise detection of EMI sources in electronic circuits. When used with spectrum analyzers such as tinySA ULTRA, it provides effective electromagnetic diagnostics without the need for external amplifiers. An ideal solution for analyzing and eliminating interference in electronic systems.

This 3-axis magnetometer provides precise magnetic field measurement in the X, Y, and Z axes within a range of ±40 mT or ±80 mT. The system is equipped with a 12-bit ADC and a CORDIC angular calculation engine, which allows for positioning within a range of 0–360°, making it suitable for applications such as magnetic encoders, robotics, and positioning systems. Communication is via an I2C interface with CRC support and speeds up to 1 MHz, and the module is compatible with 3.3V and 5V logic. STEMMA QT/Qwiic connectors enable quick connection. Adafruit 6489