SMA 20 dB attenuator – Zeenko

Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is ideal for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP1200XS

Test probe tip with 20X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 800 MHz and 1 GHz frequency band. Micsig OP20-1G

Universal oscilloscope probe with BNC plug and 10:1 voltage divider. It has a frequency range of 60 MHz and allows you to perform measurements with a maximum voltage of up to 600 V.

Probe for measuring direct current up to 800 A and alternating current up to 500 A. Operates at 5 kHz and can be connected to an oscilloscope via a BNC connector. Powered via USB. Hantek CC-800

A universal oscilloscope probe with a BNC connector and a 10:1 voltage divider. It has a frequency response of 200 MHz and allows measurements with a maximum voltage of up to 600 V. Hantek PP-200

Micsig DP series differential probe based on advanced SigOFIT technology. It offers a frequency band of 200 MHz and the ability to measure voltage up to 1500 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig DP1502

Probe for measuring direct and alternating current up to 30 A. Works in the band up to 50 MHz, can be connected to the oscilloscope through the BNC connector. Powered by USB. Micsig CP503B

The Micsig CP3008 probe is designed for precise measurement of AC/DC currents in high-voltage and high-current circuits. It is used in the analysis of switching power supplies, power converters, inverters, and testing of devices with high current loads.

Probe for measuring direct and alternating current up to 100 A. It works in the 800 kHz band, it can be connected to the oscilloscope through the BNC connector. Powered by USB. Micsig CP2100A

The P2150 oscilloscope probe with a 150 MHz bandwidth and BNC connector ensures high signal integrity and wide bandwidth, featuring switchable attenuation of 1X/10X and an input resistance of 1 MΩ/10 MΩ ±2%. The set includes accessories such as a compensation tool, identification rings, and a hook clip for easier use.

Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is ideal for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP300XS

Test probe tip with 2000X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 800 MHz and 1 GHz frequency band. Micsig OP2000-1G

A set of needle probes used for piercing wire insulation. They can be used as pin probes when working with small PCBs or connectors. Hantek HT307

A probe tip with attenuation factor of 200X. Dedicated to Micsig probes from the SigOFIT series operating in the frequency band of 100MHz, 200MHz and 350MHz. Micsig OP200-3

6-wire test leads that allow the oscilloscope to be connected to various components in the engine compartment without stripping or puncturing the insulation and without risking damage to the connectors. Hantek HT306-2.8mm

Test probe tip with 20X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 350 MHz and 500 MHz frequency bands. Micsig OP20-5