MEMS digital microphone module that communicates via I2S interface. It features low noise, high sensitivity and reliability. It allows you to add audio recording to your application, will enable voice detection, or audio transmission. It can work with systems powered by 3.3V. Full documentation with examples of use is available on the product wiki page.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
The low-power consumption micro-controller intentionally designed for Internet of Things (IoT) projects. The board integrates a Dual-Core ESP-WROOM-32 module, which supports MCU and Wi-Fi &Bluetooth dual-mode communication. DFR0478
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
Board for applications in the area of the Internet of Things (IoT). The module is based on the ESP-WROOM-32E system with 240 MHz clock, equipped with 4 MB Flash and 520 KB SRAM, as well as WiFi and Bluetooth communication. DFRobot DFR0654
Audio module that allows you to play sounds from a USB memory, microSD card, via Bluetooth or FM radio. It is equipped with a microphone, 3.5 mm audio jack and control buttons
Audio module with Jack (TRS) connector and THAT 1206 balanced line receiver. Offers low distortion and high attenuation. SparkFun BOB-14002
Module with MEMS microphone; model SPW2430 with built-in amplifier. The plate also has a 3.3 V voltage stabilizer needed to power the microphone. Adafruit 2716
This small breakout board couples an Electret microphone (100Hz–10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller’s analog-to-digital converter. Each breakout comes fully assembled and works from 2.7V up to 5.5V. BOB-12758
MEMS SPM1423 digital microphone module with PDM modulation. It communicates via the I2S interface. M5Stack U089
The VM-CLAP1 Hand Clap Sensor from Verbal Machines is a low-power, microprocessor-based audio sensor that can detect hand claps or finger snaps while ignoring background noises such as human speech or music. Pololu 2580
A module with an electret microphone and an amplifier that will allow you to detect a voice, a clap or a door slam using the analog output
Gravity: Analog Sound Sensor is a sound sensor with Gravity analogue output. The module can be supplied with 3.3 ... 5V voltage. DFRobot DFR0034
A module with an electret microphone and an amplifier that will allow you to detect a voice, a clap or a door slam using the analog output
Module with MEMS type microphone (SPH0645LM4H-B). It allows you to receive a sound signal and send it using the I2S audio interface. Powered by 1.6 ... 3.6V voltage. Adafruit 3421
Expansion board compatible with STM32 Nucleo. Allows you to prototype solutions with digital microphones. STMicroelectronics X-NUCLEO-CCA02M2
A module with a MEMS microphone and an amplifier that will allow you to detect a voice, a clap or a door slam. The board has an analog output. SparkFun BOB-19389
A module with an electret microphone and amplifier that will allow you to detect voice, clap, slam doors and other sounds using an analog or digital output. SparkFun SEN-12642
No product available!
Module with a sound sensor based on an electret microphone and LM358 amplifier. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020023
BOB-09868 - Breakout Board for ADMP401 MEMS Microphone, SparkFun
No product available!
MEMS microphone module that will allow voice detection, sound recording or audio transmission. It communicates via an I2S interface. DFRobot SEN0526